Universal job description driver impossible to compose. After all, the job responsibilities of a bus driver and an “office” driver are strikingly different. This sample driver job description is suitable for an organization in which the driver is engaged in the "transportation" of the first person of the company and other employees.

Job description driver

APPROVE
CEO
Surname I.O. ________________
"________"_____________ ____ G.

1. GENERAL PROVISIONS

1.1. The driver belongs to the category of technical performers.
1.2. The driver is appointed to the position and dismissed from it by order of the general director of the company.
1.3. The driver reports directly to the general director / head of the structural division of the company.
1.4. During the absence of the driver, his rights and obligations are transferred to another official, which is announced in the order for the organization.
1.5. A person who meets the following requirements is appointed to the position of driver: category B rights, driving experience of 2 years.
1.6. The driver must know:
- Rules traffic, penalties for their violation;
— basic specifications And general device car, purpose, device, principle of operation, operation and maintenance of units, mechanisms and devices of the car;
- rules for maintaining the car, caring for the body and interior, keeping them clean and in a condition favorable for long-term operation;
- signs, causes and dangerous consequences of malfunctions that occur during the operation of the car, ways to detect and eliminate them;
- Car maintenance procedure.
1.7. The driver is guided in his activities:
- legislative acts of the Russian Federation;
— the Charter of the company, the Internal Labor Regulations, other regulatory acts of the company;
- orders and directives of the management;
- this job description.

1. RESPONSIBILITIES OF THE DRIVER

The driver performs the following duties:
2.1. Provides timely delivery of the car.
2.2. Ensures the technically sound condition of the car assigned to the driver.
2.3. Takes measures for the safety of the car and the property in it: does not leave the car unattended, without fail puts the car on an alarm in any case of leaving the passenger compartment, blocks all the car doors during movement and parking.
2.4. Carries out driving a car, ensuring the safety of life and health of passengers and the technically sound condition of the car itself.
2.5. Monitors the technical condition of the vehicle, performs independently the necessary work to ensure it safe operation(according to the user manual).
2.6. Timely passes Maintenance service center and technical inspection.
2.7. Keeps the engine, body and interior of the car clean, protects them with appropriate care products for certain surfaces.
2.8. Do not use alcohol before or during work, psychotropic, sleeping pills and other drugs that reduce the attention, reaction and performance of the human body.
2.9. Before leaving, he clearly works out the route, coordinates it with the senior of the group and the immediate supervisor.
2.10. Maintains waybills, noting routes, distance traveled, fuel consumption.
2.11. At the end of the working day, he leaves the car entrusted to him in a guarded parking lot / garage.
2.12. Performs individual official assignments of his immediate supervisor.

1. DRIVER RIGHTS

The driver has the right:
3.1. Require passengers to comply with the Rules of the Road (fasten their seat belts, get on and off at places permitted for this, etc.).
3.2. Receive information in the amount necessary to solve the tasks.
3.3. Submit proposals to the management for improving their work, as well as those aimed at improving the safety and trouble-free operation of the vehicle.
3.4. Require management to create normal conditions for the performance of official duties and the safety of all documents resulting from the activities of the company.
3.5. Make decisions within your competence.

1. DRIVER RESPONSIBILITY

4.1. For non-performance and / or untimely, negligent performance of their duties.
4.2. For non-compliance with current instructions, orders and orders for the preservation of trade secrets and confidential information.
4.3. For violation of the internal labor regulations, labor discipline, safety and fire safety rules.

Job description of the driver of a passenger car

1. GENERAL PROVISIONS

1.1. This Instruction defines the duties and rights of the Driver working on a company car.

1.2. The driver is hired and dismissed from her by order of the head of the enterprise in the prescribed manner.

1.3. The driver reports organizationally to the Chief Mechanic and directly to the official who has the official car at his disposal.

1. QUALIFICATION REQUIREMENTS.

2.1. A person who has the right to drive a single passenger car and truck of all types and brands classified in one or both categories of vehicles "B" or "C" is appointed to the position of Class III Driver.

2.2. The qualification of a Class II Driver can be awarded with continuous work experience as a Driver car III class of at least 2 years, who has a driver's license with a mark giving the right to drive cars of all types and brands classified as vehicles "B", "C", "E".

2.3. The qualification of a Class I Driver can be awarded with continuous work experience as a Class II Car Driver for at least 1 year, who has been trained and received an appropriate certificate, and also has a driver’s license with a mark giving the right to drive cars of all types and brands, classified to categories of vehicles "B", "C", "D" and "E".E

2.3. The qualification of a Class I Driver can be awarded with continuous work experience as a Class II Car Driver for at least 1 year, who has been trained and received an appropriate certificate, and also has a driver’s license with a mark giving the right to drive cars of all types and brands, classified to vehicle categories

1. THE DRIVER SHOULD KNOW:

3.1. Rules of the road, penalties for their violation.

3.2. The main technical characteristics and general arrangement of the car, instrument and counter readings, controls (purpose of keys, buttons, handles, etc.).

3.3. The order of installation and removal of alarm systems, the nature and conditions of their operation.

3.4. Rules for maintaining a car, caring for the body and interior, keeping them clean and in a condition favorable for long-term operation (do not wash the body in direct sunlight, hot water in winter).

3.5. The timing of the next maintenance, technical inspection, checking tire pressure, tire wear, steering wheel free play angle, etc. according to the vehicle's operating instructions.

3.6. Rules for filling out primary documents for accounting for the operation of serviced vehicles.

3.7. Causes, methods for detecting and eliminating malfunctions that occurred during operation vehicle.

1. DUTIES

The driver must:

4.1. To ensure the correct smooth professional driving of the car, which maximizes the safety of the life and health of passengers and the technically sound condition of the car itself. Do not use sound signals and sudden overtaking of vehicles in front unless absolutely necessary. The driver is obliged and able to foresee any traffic situation; choose the speed of movement and distance, excluding the occurrence of emergency.

4.2. Do not leave the vehicle unattended out of sight for any minimum period of time that gives the chance of theft of the vehicle or theft of any items from the passenger compartment. Park your car only in guarded parking lots.

4.3. It is mandatory to put the car on the alarm in any case of exit from the passenger compartment. While driving and parking, all vehicle doors must be locked. When leaving the car (landing), you must make sure that there is no potential danger.

4.4. Monitor the technical condition of the vehicle, perform independently the necessary work to ensure its safe operation (according to the operating instructions), timely undergo maintenance at the service center and technical inspection.

4.6. Strictly follow all orders of the head of the enterprise and his immediate supervisor. Ensure timely vehicle delivery.

4.7. Communicate truthful information about your health to your immediate supervisor.

4.8. Do not use alcohol before or during work, psychotropic, sleeping pills, antidepressants and other drugs that reduce the attention, reaction and performance of the human body.

4.9. Categorically not allow cases of transportation of any passengers or cargo at one's own discretion, as well as any kind of use of the car for personal purposes without the permission of the management. Always be at the workplace in the car or in close proximity to it.

4.10. Keep daily waybills, noting routes, kilometers traveled, fuel consumption.

4.11. Pay close attention to the surrounding road conditions. Report to the immediate supervisor all your suspicions regarding security issues, make suggestions for improving it.

4.12. Do not engage in extraneous activities during working hours. Show a creative approach to their immediate responsibilities, try to be useful to the enterprise in its current business activities.

1. THE RIGHTS

The driver has the right:

5.1. Require passengers to comply with the rules of conduct, cleanliness, wear a seat belt.

5.2. Make suggestions to the management aimed at improving the safety and trouble-free operation of the vehicle, as well as on any other issues related to the implementation of this Instruction.

5.3. Get acquainted with the draft decisions of the management of the enterprise relating to its activities.

1. RESPONSIBILITY

The driver is responsible:

6.1. For non-fulfillment (improper fulfillment) of their official duties provided for by this job description, to the extent determined by the current labor legislation.

6.2. For offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal and civil legislation.

6.3. For causing material damage - within the limits determined by the current labor, criminal and civil legislation.

1. OCCUPATIONAL SAFETY AND HEALTH

7.1. The driver must know and comply with the provisions of the Law "On Labor Protection", other regulatory legal acts on labor protection, as well as the requirements of the orders, instructions, and regulations in force at the enterprise that regulate labor protection issues.

Job description of a forwarding driver

1. GENERAL PROVISIONS

1.1. This Instruction defines the functional duties, rights and responsibilities of the forwarding driver of Trigona LLC (Enterprise).

1.2. The term "Forwarding Driver" means a full-time employee of the Enterprise operating in official purposes on a permanent or temporary basis, a car owned by the Company or a car at its disposal.

1.3. The forwarding driver reports directly to the General Director of the Enterprise.

1.4. The delivery driver must know:

1.4.1. Rules of the road, penalties for their violation.

1.4.2. Specifications and the general structure of the car, instrument and counter readings, controls (purpose of keys, buttons, handles, etc.).

1.4.3. The order of installation and removal of alarm systems, the nature and conditions of their operation.

1.4.4. Rules for maintaining a car, caring for the body and interior, keeping them clean and in a condition favorable for long-term operation (do not wash the body in direct sunlight, hot water in winter, apply protective lotions, washing liquids, etc. in a timely manner).

1.4.5. The timing of the next maintenance inspection, checking tire pressure, tire wear, steering wheel free play angle, etc. according to the vehicle's operating instructions.

1.5. In his activities, the forwarding driver is guided by the Charter of the Enterprise, the internal labor schedule, this instruction, orders and orders of the head of the enterprise.

1. FUNCTIONS

2.1. Efficient and safe vehicle operation.

2.2. Ensuring the proper technical condition of the car.

2.3. Ensuring the safety of entrusted property, including a car.

2.4. Ensuring forwarding and courier functions for the delivery and maintenance of materials, as well as accounting and other documents.

1. DUTIES

To perform the functions assigned to him, the driver-forwarding agent must:

3.1. To ensure the correct smooth professional driving of the car, which maximizes the safety of the life and health of passengers and the technically sound condition of the car itself. Do not use sound signals and sudden overtaking of vehicles in front unless absolutely necessary. Anticipate any traffic situation; choose the speed of movement and distance, excluding the occurrence of an emergency.

3.2. Do not leave the vehicle unattended out of sight for any minimum period of time that gives the chance of theft of the vehicle or theft of any items from the passenger compartment. If possible, park your car only in guarded parking lots.

3.3. It is mandatory to put the car on the alarm in any case of exit from the passenger compartment. While driving and parking, all vehicle doors must be locked. When leaving the car (landing), you must make sure that there is no potential danger.

3.4. Ensure that the car is parked in a garage / guarded parking lot to ensure the safety of the car.

3.5. Monitor the technical condition of the vehicle, perform independently the necessary work to ensure its safe operation (according to the operating instructions), timely undergo maintenance at the service center and technical inspection. Timely submit applications necessary to ensure the proper technical condition of the car (regulated by the reference and technical literature for this car).

3.6. Ensure timely submission of fuel requests.

3.8. Ensure timely vehicle delivery.

3.9. Strictly comply with all requirements of the Regulations on the division, orders of the head of the Enterprise.

3.10. Report reliable information about your health to the manager.

3.11. Do not use alcohol, psychotropic, sleeping pills, and other drugs that affect the attention, reaction and performance of the human body before or during work.

3.12. Do not allow cases of transportation of any passengers or cargo at your own discretion, as well as any kind of use of the car for personal purposes without the permission of the management.

3.13. Maintain daily waybills, noting the routes, distance traveled, speedometer readings before departure and upon return, the amount of time worked. Require the person who used the car to mark the waybill.

3.14. Fulfill the instructions of the head of the enterprise and the chief accountant for the transportation of goods, execution and delivery of documents to the destination.

1. THE RIGHTS

The forwarding driver has the right to:

4.1. Make suggestions to the management aimed at improving the safety and trouble-free operation of the vehicle, as well as on any other issues related to the implementation of this Instruction.

1. RESPONSIBILITY

The delivery driver is responsible for:

5.1. For non-fulfillment (improper fulfillment) of their official duties provided for by this job description, to the extent determined by the current labor legislation of the Russian Federation.

5.2. For offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal and civil legislation of the Russian Federation.

5.3. For causing material damage - within the limits determined by the current labor, criminal and civil legislation of the Russian Federation.

1. FINAL PROVISIONS

6.1. This job description is communicated to the forwarding driver for review against signature in the employment contract.

__________________________________________________________________

(full name of the enterprisefrom indication of subordination)

1. APPROVED

Order _______________________

(employer position and

_____________________________

Business name)

_________________ № _________

2. (day month Year)

INSTRUCTIONS

ON LABOR SAFETY

FOR THE DRIVER OF THE TRANSPORT-HARVESTING MACHINE

( for cleaning railway stations,

stations and stops. )

№___________

1. GENERAL SAFETY REQUIREMENTS

1.1. This labor protection instruction for the driver of a transport harvester (hereinafter referred to as the Instruction) establishes the basic safety requirements for drivers using transport harvesters (universal harvesters, snow loaders, auto and electric loaders, electric cars, electric tractors) for cleaning railway stations, stations and stops.

1.2. Persons not younger than 18 years of age who have passed a preliminary medical examination, introductory and primary briefing at the workplace, training, internship and knowledge testing are allowed to work on maintenance of transport and harvesting machines.

In the process of work, drivers of transport-harvesting machines (hereinafter referred to as drivers) must undergo repeated, at least once every three months, and unscheduled briefings, as well as periodic medical examinations.

In order to determine the state of health and the absence of alcohol and other drugs in the body of the driver, drivers must undergo daily (before the start of the shift) medical examinations.

1.3. Drivers servicing transport and harvesters are required to have a certificate for the right to drive them, know the Rules of the Road, the main sections of the Instructions for signaling on railways ah of Ukraine, the relevant sections of the Rules technical operation railways of Ukraine. In addition, drivers servicing cars with a license plate are required to have a driver's license issued by the State Automobile Inspectorate of the Ministry of Internal Affairs of Ukraine.

1.4. Each transport and harvester must be assigned to a specific driver. Another employee who has the right to operate it may be allowed to work on this machine only with the permission of the shop manager or chief mechanic.

1.5. Only workers who have passed qualification tests for the right to operate them, including the study of technical instructions and passports of these machines, with the permission of the head of the shop or the chief mechanic.

1.6. The driver must know:

features of driving cars in adverse weather conditions and basic techniques for the prevention of road accidents;

purpose, device, principle of operation of the machine assigned to it, as well as trailed and mounted units, mechanisms and devices attached to it;

instructions for the technical operation and maintenance of the machine;

safety requirements when working with trailed and mounted units, mechanisms and devices;

signs, causes and dangerous consequences of malfunctions that occur during the operation of the machine, methods for their detection and elimination;

the procedure for storing a car in a garage and in open parking lots;

the impact on a person of dangerous and harmful production factors that arise during work;

rules for providing first (pre-medical) aid in case of accidents;

rules for the use of primary fire extinguishing means;

industrial hygiene and fire safety requirements.

1.7. The driver must:

perform only the work assigned by the head on the machine assigned to him;

observe safety rules when repairing a car on the line and in the garage;

master safe working practices;

comply with the requirements of prohibitory, warning, indicative and prescriptive signs and inscriptions, as well as signals given by machinists, train compilers, drivers of other vehicles and workers employed repair work on the territory of the railway station, railway station;

pass through the area railway station along established routes, footpaths, tunnels, passages and crossings;

be extremely careful in places of traffic;

observe the rules of internal labor regulations;

fulfill the requirements of work and rest regimes.

1.8. The driver is prohibited from:

leave the car unattended if it is on a passenger platform or near railway tracks;

cross the railroad tracks in unspecified places;

drive a car in pain, tired state, as well as in a state of alcoholic or drug intoxication;

transfer control of the vehicle to persons not specified in the order - task (waybill);

to clean the territory at night with insufficient lighting;

go to the line without a first aid kit and a fire extinguisher;

deviate from the route indicated in the order - task (waybill) and use the car for personal purposes;

cross paths in front of moving vehicles;

be on the territory and in the premises of the railway station in places marked with the sign "Caution! Oversized place", as well as near these places when passing rolling stock.

1.9. Checking the technical serviceability of the transport and harvesting machine must be carried out before leaving for work by the mechanic on duty responsible for its good condition and confirmed by the note of the responsible person and the signature of the driver in the order - assignment (waybill).

1.10. While driving a transport and harvester, the driver may be affected by the following main dangerous and harmful production factors:

moving vehicles, mechanisms, rolling stock;

objects falling from a height;

increased dust and gas content in the air of the working area;

increased noise level in the workplace;

increased level of vibration;

increased voltage in the electrical circuit, the closure of which can occur through the human body;

insufficient illumination of the working area;

low or high temperature, high humidity and air mobility of the working area;

physical overload;

neuropsychic overload.

1.11. The driver must be provided with the following PPE:

cotton suit;

raincoat from a raincoat tent or tarpaulin (in the absence of a closed cabin);

combined gloves;

tarpaulin boots.

For outdoor work in winter additionally:

heat-protective suit;

felt boots;

galoshes on felt boots.

1.12. The driver must comply with the following fire safety requirements:

do not smoke or use open flames when checking the engine power system and while working in the cab;

do not perform work related to the use of open fire, electric gas welding, blowtorches, torches;

do not burn containers and do not make fires near the car;

do not store explosive substances, flammable and combustible liquids in the cab or body;

immediately inform the mechanic on duty about all malfunctions of electrical appliances and electrical equipment;

if a sharp smell of gasoline appears while driving, immediately stop the car, identify the cause of its appearance and eliminate the malfunction;

Smoking only in designated and designated areas.

1.13. Personal clothing and overalls must be stored separately in lockers in the dressing room. It is prohibited to take work clothes outside the enterprise.

1.14. The driver is obliged to monitor the serviceability of overalls, timely handing it over for washing and repair, as well as keep the lockers clean and tidy.

1.15. Eating should only be in canteens, buffets or specially designated rooms with appropriate equipment. Before eating, wash your hands thoroughly with warm water and soap.

1.16. While on the railway tracks, the driver must comply with the following requirements:

to the place of work and from work to pass only by specially established routes, marked with signs "Service Passage";

pass along the tracks only along the side of the road or in the middle of the track, paying attention to the wagons and locomotives moving along the adjacent tracks;

cross the tracks only at a right angle, after making sure that there are no locomotives or wagons moving at a dangerous distance in this place;

cross the track occupied by the rolling stock, using only the transitional platforms of the wagons;

when leaving the wagon, hold on to the handrails and position yourself facing the wagon, having previously examined the place of the descent and made sure that the handrails and steps are in good condition, as well as that there are no locomotives and wagons moving along the adjacent track;

bypass groups of wagons or locomotives standing on the way at a distance of at least 5 m from the automatic coupler;

pass between uncoupled wagons if the distance between the automatic couplers of these wagons is at least 10 m;

pay attention to indications of enclosing traffic lights, sound signals and warning signs.

1.17. The driver is prohibited from:

cross or run across the tracks in front of a moving rolling stock, locomotive, engine locomotive, trolley or other vehicle;

stand or sit on a rail;

sit on the steps of wagons or locomotives and get off them while moving;

to be on the inter-track between trains during their non-stop movement along adjacent tracks;

cross points equipped with electrical interlocking at the locations of the points and cross fastenings of turnouts, stand between the point and the frame rail or into the gutters on the turnout and the ends of reinforced concrete sleepers.

1.18. When entering the track from a room or buildings that impair the visibility of the track, you must first make sure that there is no rolling stock moving along it.

1.19. In case of injury or illness, the driver must stop work, notify the work manager and seek help from a first-aid post or the nearest medical facility.

If other workers are injured, they must be given first medical care, immediately notify the administration and, if necessary, take the victim to a medical facility.

1.20. If violations of this Instruction are found, as well as malfunctions of the machine, equipment, tools, protective devices, personal protective equipment and fire extinguishing, the driver must immediately inform the mechanic of the garage, and in his absence - to a higher manager.

1.21. Knowledge and compliance by the driver with the requirements of this Instruction are duty, and their violation - a violation of labor discipline, which entails, depending on the consequences, disciplinary or other liability in accordance with the legislation of Ukraine.

2. SAFETY REQUIREMENTS BEFORE WORKING START

2.1. Upon receipt of the outfit - tasks ( waybill) the driver must familiarize himself with the working conditions, with the type of cargo being removed or transported.

2.2. Before leaving for work, the driver must check:

possession of a driving license;

the correctness of filling out the order - tasks (waybill) and sign it;

technical serviceability of the machine, which guarantees the safety of work;

the serviceability of the operation of the brakes, clutch, friction clutches, gearboxes;

reliability of fastening of levers and steering rods, as well as steering play;

tire condition and pressure;

serviceability of lighting devices, brake light, direction indicators, sound (alert) signal;

no leakage of fuel, oil, water, antifreeze;

availability of tools, accessories and portable emergency stop signs, as well as signal warning signs (orange or yellow flashing beacon, red flag or shield) installed on the transport and harvester when working on the platform;

filling the car with fuel, oil, water, antifreeze and brake fluid;

electrolyte level in batteries;

availability and serviceability of blocking and other devices.

2.3. The driver of the universal harvester must check the reliability of fastening and connection of trailed and mounted units, mechanisms and devices.

2.4. The driver of an auto- and electric loader must check the idle operation of the lifting mechanisms and special drives.

2.5. The driver of an electric car must check the serviceability of the brakes on the go, the operation of the electric lock.

2.6. The driver must not start work if a malfunction is detected in which the operation of the vehicle is prohibited by the Rules of the Road or at least one of the following defects occurs:

brakes not adjusted or faulty;

the brake signal is faulty;

motor overheating or electric motor sparking;

low tire pressure, through holes, damage to the cord;

damage to electrical wires;

leaks in the connections of oil pipelines, gasoline pipelines, batteries;

faulty lighting and other malfunctions indicated in the machine's operating instructions.

2.7. The driver of an auto- and electric forklift should not start work if a crack is found in the welds on the frame, the forklift carriage and load gripping devices, loosening of the fastening of the cargo chains, hydraulic cylinder fingers.

2.8. Before starting work, the driver must put on the working clothes and safety shoes that are due to him, and put them in order.

The driver must not remove overalls and safety shoes during the entire working time.

2.9. If, during the inspection and testing of the vehicle, faults are found that cannot be eliminated on their own, the driver must inform the mechanic on duty or the person responsible for the technical condition and safe operation of the vehicles, and not start work until they are eliminated.

3. SAFETY REQUIREMENTS DURING WORK

3.1. Safety requirements when working on all types of transport and harvesting machines

3.1.1. During work, the driver must comply with the rules of the road, the rules for loading and unloading operations, apply safe working methods when repairing and maintaining the machine.

3.1.2. While driving, the driver must:

maintain the speed of the vehicle in accordance with the requirements of the Rules of the Road, road signs and taking into account meteorological conditions;

observe the readings of control devices;

periodically check and take measures to remove stones and other objects stuck between the tires of the wheels.

3.1.3. Transport and harvesting machines should only work on the territory with a good-quality hard and smooth surface: asphalt, concrete, paving stones.

3.1.4. The cleaned area and passages of railway stations, railway stations must be well lit and free from foreign objects.

3.1.5. When crossing railway tracks, the driver must make sure that there is no approaching rolling stock. In the case of the movement of rolling stock, it is necessary to stop the car and wait for the track to be cleared.

3.1.6. Railway tracks The driver must cross the crossings at low speed without changing gears.

3.1.7. The driver must maintain such a distance from the vehicle in front, which would allow avoiding a collision or collision in the event of a sudden stop of the vehicle in front.

3.1.8. The driver must observe the following speed:

on passenger platforms - no higher than 3 km/h;

on the territory of the railway station, railway station and on crossings and slopes - no higher than 5 km / h;

on the territory adjacent to the railway station, railway station - no more than 10 km / h.

3.1.9. In all cases where there is a danger of an unexpected meeting with people, the driver must give a sound signal no closer than 5 meters.

3.1.10. When passing for cleaning on the forecourt and platforms, when there are passengers on them, the driver is obliged to warn them with a signal about the approach of the car and take special care when driving. Turning off the rotating beacon during the entire time of operation of the transport and harvester is not allowed.

The driver must also give a warning sound signal when starting the car from a place and when changing direction.

3.1.11. The movement of vehicles on the platforms should be carried out no closer than 1 m from the edge of the platform.

When cleaning platforms from snow, it is allowed to bring the machine closer to the edge of the platforms no closer than 0.5 m.

3.1.12. The driver is prohibited from:

allow persons who do not have the right to operate the machine, repair and start the engine;

allow persons who are not related to the work performed to be in the cab and body;

transport people on footboards;

rest or sleep in the cab and body during parking with the engine running;

leave the machine under a lifted or moved load;

leave the car on railway tracks and crossings, in public driveways and in fire lanes;

stepping on and running into electrical wires and cables;

touch broken wires and other easily accessible live parts.

3.1.13. Before filling the engine cooling system with antifreeze, it is necessary to check for leakage and, if found, eliminate it.

Filling the engine cooling system with antifreeze must be done using dishes specially designed for this purpose.

It is forbidden to pour antifreeze with a hose by suction by mouth.

Antifreeze should not be poured up to the radiator neck, but in such a way that during engine operation (when heated), antifreeze does not leak due to overflow of the cooling system.

Protect antifreeze from oil products getting into it, since during engine operation they lead to foaming of antifreeze.

After each operation with antifreeze (receiving, refueling), hands must be thoroughly washed with soap and water.

3.2. Safety requirements when working on a universal harvester

3.2.1. Passenger platforms should only be cleaned during the break between trains. It is impossible to water the platform if there are electric trains with a raised pantograph on the railway track.

3.2.2. During the movement of the machine, stones, mounds, potholes and other obstacles should be avoided, while attachments, mechanisms and devices should be raised, and the upper engine guard should be tightly closed.

3.2.3. When working on the territory adjacent to the railway station, railway station and on passenger platforms, the driver must not turn the machine sharply and sharply.

3.2.4. The height of the shoveled snow shaft should not exceed 0.5 m in order to avoid slipping of the machine and the danger of it slipping to the side.

3.2.5. While the machine is in operation, the driver must ensure that when watering, washing or clearing snow in working area there were no strangers.

3.2.6. When turning or changing the position of the working bodies, the driver is obliged to make sure that these operations are completely safe for passengers. Particular care must be taken when working in icy, foggy or poor visibility conditions.

3.2.7. When parking a trailer, the driver must put stops under the wheels.

3.2.8. The driver must not allow the passage of people on trailed and mounted units, mechanisms and devices.

3.2.9. The driver must not remove any objects from under the trailers and attachments of the machine while the engine is running.

3.2.10. Starting an automobile engine is usually done with a starter. When starting the engine with the crank, it is necessary to clasp it with all fingers on one side, without clamping the handle with your thumb. Move the handle from bottom to top.

Starting the engine by towing is not allowed.

3.3. Snow loader safety requirements

3.3.1. When moving through the territory of the railway station, the station, the driver must transfer the boom and shovel on the snow loader to the transport position.

To prevent the snow loader from tipping over, its path should not have a transverse slope of more than 15 °, when driving on sharp turns, the speed should be reduced to 5 km / h.

3.3.2. When starting off or at the beginning of work, it is necessary to give a sound signal.

3.3.3. Upon arrival at the work site, the driver must lower the shovel to the loading horizon and raise the conveyor boom to the required height.

3.3.4. Before loading the snow, the driver must make sure that there are no people in the area of ​​the work ahead and between the snow loader and the vehicle on which the snow is loaded.

3.3.5. When loading snow, the driver must:

turn on the mechanism only with the shovel lowered;

before lifting or lowering a shovel or conveyor, first make sure that there are no workers involved in the removal of snow or foreign objects near these nodes;

constantly monitor the pressure in the hydraulic system, the forward speed of the conveyor and the amount of snow loaded.

3.3.6. When the snow loader is in operation, workers engaged in snow removal are not allowed to be on the conveyor, as well as at a distance of less than 5 m from its paws.

3.3.7. The driver can increase the speed of snow supply only if the snow loader easily overcomes the snow bank.

3.3.8. Let the snow loader idle for a while before clearing snow from the snow loader's shovel and conveyor.

3.3.9. It is necessary to clean the shovels and conveyor of the snow loader from frozen snow only after the mechanism has completely stopped using shovels, scrapers and other hand tools.

3.4. Safety requirements when working on a car and electric forklift

3.4.1. The driver must follow the instructions of the slinger for lifting, lowering and moving the load. The "Stop" signal should be carried out in all cases, no matter who gave it.

3.4.2. Move the auto- and electric forklift from a place smoothly, at low engine speeds. During movement, the load or gripper should be at a distance of 300 - 400 mm from the ground or floor surface with the frame of the load lifter tilted back.

3.4.3. Do not make sudden braking while driving. The movement of an auto- and electric loader with a load is allowed with a slope of not more than 7 °. When transporting a load downhill move in reverse, on the slope - front. It is forbidden to lift and lower the load while moving.

3.4.4. The fork tines should be set at the same distance from the center of the forklift carriage. Place the center of gravity of the load as close as possible to the front walls of the forks and to the middle of the forklift carriage.

3.4.5. Small piece cargo is allowed to be lifted only if it is placed in a special container that protects it from falling.

3.4.6. Do not allow people to stay under the load taken on the working attachment of the forklift.

3.4.7. Before lifting and lowering the load, put the forklift on the handbrake, and for the electric forklift, put the brake pedal on the latch.

3.4.8. Do not move an auto-, electric forklift with a forward-tilted forklift frame.

3.4.9. When transporting cargo, the driver must comply with the following requirements:

lift the load from the supporting surface to a height of 200 - 300 mm;

in order to prevent the load from slipping off the forks, install its frame parallel to the supporting surface or tilt it back;

start moving at the first speed;

make turns smoothly;

avoid transverse slopes.

3.4.10. When driving an auto- and electric forklift, always watch the upper obstacles (wires, arches and other obstacles).

3.4.11. It is forbidden to tear off a frozen or clamped load, to seize the load if there is no clearance under it for inserting the forks.

3.4.12. After transportation, the load must be placed on gaskets that ensure the free exit of the gripping fork from under the load.

3.4.13. The load on the gripping fork should be placed in such a way that the resulting tipping moment is minimal. In this case, the load must be pressed against the vertical part of the gripping fork.

3.4.14. Before lifting a load, the driver must fulfill the following requirements:

make sure that the place from which the load should be lifted or lowered is suitable for this;

set the forks in width symmetrically with respect to the vertical frame and parallel to the horizontal plane;

drive up to the load at the first speed until the forks fit under the load (pallet) to be lifted;

make sure that the load is installed close to the frame, evenly distributed on the forks, does not extend beyond the forks for more than 1/3 of their length, and secured, if necessary, with a tie-down wire;

make sure that the upper part of the load does not protrude above the carriage by more than 1/3 of its height;

make sure that the goods on the pallet are formed into a stable and tight package, the dimensions of which do not exceed the limits of the pallet by more than 20 mm on each side.

3.4.15. If, for any reason, the lifting mechanism carriage stops moving along the guides and the forks do not rise or fall, the driver should stop work and inform the work manager about this.

3.4.16. When working on a car and electric forklift, it is prohibited:

stack the load above the protective device that protects the driver's workplace from falling load on him through the frame;

lift cargo, the mass of which exceeds the carrying capacity, as well as cargo, the center of gravity of which goes beyond the forks;

apply additional counterweights;

push the load from the stacks;

drag the load;

lift and move cargo with only one fork;

lift, lower and transport people on forks.

3.4.17. The driver of an electric forklift is prohibited from:

operate the forklift with the panel removed from the control panel and the battery open.

3.4.18. When leaving the auto- and electric forklift, the driver must remove the key from the electric control circuit switch and set it to the parking brake.

3.4.19. Long loads are allowed to be transported only in open areas, previously tied in such a way that the possibility of their falling is excluded.

3.4.20. In order to avoid tipping over of the auto- and electric loader under adverse weather conditions (icy, wet or slippery road), sudden braking is not allowed. In the event of a loss of a stable position by the auto- and electric loader (when the rear wheels come off the supporting surface), the load must be lowered immediately.

3.5. Safety requirements when working on an electric car and an electric tractor

3.5.1. Electric cars, electric tractors can be operated on passenger platforms and in other places on the territory of a railway station, station, where the slope does not exceed 15 °. When stopping on a slope, these vehicles must be braked hand brake. Parking them on a slope of more than 8 ° is not allowed.

3.5.2. The driver is obliged to monitor the correct loading, lashing the load on the trolley so that its stability is ensured during transportation, as well as its safety on the way.

3.5.3. When transporting cargo that can arbitrarily move around the platform of an electric car, the driver must require the installation of safety racks and reliable fastening of the cargo. It is prohibited to use an electric car without fulfilling these requirements.

3.5.4. Electrical braking is not permitted under normal conditions and should only be used in extreme cases where there is a risk of collision with people, other vehicles and other obstacles.

3.5.5. The driver is allowed to attach luggage or container carts, but not more than ten.

The weight of the trailer trolley together with the load must not exceed the carrying capacity of the electric car, electric tractor.

3.5.6. An electric car, an electric tractor must be equipped with a reliable towing device with a lock, excluding spontaneous disengagement.

3.5.7. When working on an electric car, electric tractor, it is prohibited to tow carts of an unspecified type, dragging loads and devices by dragging, as well as towing with two electric cars, electric tractors.

3.5.8. In all cases, the movement of the electric car should be carried out forward by the platform on which the driver is standing, except for cases of maneuvering at a short distance of up to 10 meters, when it is necessary to supply the electric car for loading or unloading in warehouses platform forward.

3.5.9. If it is necessary to switch the electric car to reverse, the driver must stop it, turn his face in the direction of the subsequent movement, and then reverse.

3.5.10. The driver is prohibited from switching the electric car to reverse while driving until it comes to a complete stop, except in cases of obvious danger.

3.5.11. All bulk cargo should only be transported in containers or crates. The height of the placement of cargo on the platform of the electric car should not exceed the racks of the controller, the cargo should not protrude beyond the platform.

3.5.12. When leaving the electric car (electric tractor) and at the end of work, you must remove the battery plug from the socket and lock it.

3.5.13. During the boarding and disembarkation of passengers from the cars, the movement of electric cars and electric tractors on the platform is not allowed.

3.6. Safety requirements for the maintenance of transport and harvesters

3.6.1. Maintenance and repair of transport harvesters should be carried out in accordance with the requirements of the instructions for their operation.

3.6.2. To ensure safety during the repair and maintenance of the machine, the driver must:

work with a jack, installing safety trags and brake pads under the wheels

remove heavy units and assemblies with appropriate precautions (serviceable electric hoists or hand winches);

lubricate, adjust and perform other repairs with the engine off;

Use only correct tools for repairs.

3.6.3. Leave the car at stops, parking lots and when refueling is possible only with the engine turned off.

3.6.4. The delivery of the machine, which has failed, to the garage should be carried out by towing with a tractor. It is forbidden to push the machine with another vehicle.

3.6.5. When towing the machine, it is necessary to use a special towing device with a test tag.

When towing on a flexible hitch, it is necessary to ensure the distance between the towing and towed machine within 4-6 m, on a rigid hitch - no more than 4 m.

3.6.6. When servicing and repairing the machine, it is forbidden for unauthorized persons to stay at the workplace.

3.6.7. All operations related to maintenance and repair must be carried out after the machine is completely stopped, it is braked, the gear lever is in the neutral position, the engine is stopped, and when the working bodies are lowered to the ground or mounted on clamps (special racks). At least two stops must be placed under the wheels on opposite sides of the wheel.

With the engine running, only checking the operation of the brakes and engine systems is allowed.

3.6.8. During inspections, adjustment, adjustment and repair operations, when the driver is forced to be under the working bodies raised and installed on the clamps (special racks), it is forbidden for other employees and unauthorized persons to be near the levers and control handles of the working bodies and touch these levers and handles.

3.6.9. During the maintenance and repair of the machine, the driver is obliged to use only serviceable tools and a portable lamp with a safety net with a voltage of not more than 42 V, and in the inspection ditch not more than 12 V.

3.6.10. Hammers, sledgehammers must be mounted on handles made of hard wood and wedged with metal wedges. Chisels, barbs and cores should not have knocked down and beveled impact parts, burrs on the side edges and places where they are clamped by hand.

3.6.11. The size of the wrenches during operation must match the size of the nuts and bolts. If you need to have a long lever, you should use a wrench with an extended handle. It is forbidden to increase the key with another key.

3.6.12. Files and screwdrivers must be firmly fixed in the handles with metal rings.

The surface of the wooden handles of the tools must be smooth, without burrs and cracks.

3.6.13. When working with a chisel and other hand tools when cutting metal, it is necessary to wear safety goggles.

3.6.14. Wedges or chisels should be supported during operation by wedge holders with a handle length of at least 70 cm.

3.6.15. To lift working bodies during repairs, it is necessary to use serviceable lifting equipment (hoists, jacks, etc.).

3.6.16. It is necessary to use special devices or pullers for mounting and dismantling of units and attachments.

It is forbidden to stay under the removed (installed) machine components.

3.6.17. Aggregates, components and wheels weighing more than 15 kg must be moved only with the help of lifting and transport equipment and small-scale mechanization.

3.6.18. Before dismantling hydraulic system and lubrication systems must be drained working fluid and oil in special containers.

3.6.19. Workplace should not be cluttered with unnecessary materials and tools.

Cleaning material and rags should be stored in a metal box.

3.6.20. When carrying by hand batteries stretcher must be used.

3.6.21. It is forbidden to tighten connections, couplings on pipelines under pressure of liquid, oil, fuel, air.

3.6.22. When removing the filler plug of a hot engine coolant radiator, be careful, for example, cover it with a thick cloth or mitt. Add coolant to the radiator with the engine running at low speed or stopped.

Do not add coolant to the radiator of an overheated engine and do not bend over the filler hole.

3.6.23. Use a pump to transfer fuel when refueling and to purge fuel lines.

3.6.24. After maintenance and repair, before starting the engine, make sure that all hydraulic control drive mechanisms are set to the neutral (off) position.

It is forbidden to start and operate an internal combustion engine in enclosed spaces.

3.6.25. To inspect the components of the machine being repaired, crawling under it with the engine running is prohibited.

3.6.26. Dismantling of tires and a disk of a wheel should be made only after complete removal of pressure in the chamber of the tire. Work on remounting tires should be carried out at a specially equipped place with the presence and use of safety devices (studs, staples, etc.).

3.6.27. When remounting, use only a special tool designed for this type of wheel.

3.6.28. In order to avoid damage to wheel parts, tires and chipping off of small metal parts when dismantling the wheel, hitting the blades should be done with an aluminum sledgehammer.

3.6.29. When installing tubes, tires and wheels, do not allow dirt and other objects to get into the mounted wheel. If water or dirt gets into the chamber, tire or other parts of the mounted wheel, they should be washed and wiped dry.

3.6.30. Before dismantling each tire that was in operation, it is necessary to inspect the inner and outer surfaces for the absence of foreign objects on them. The inner surface should be wiped with a special scraper or a bunch of ends. It is forbidden to feel the inner surface with unprotected hands. Removal of detected foreign objects (nails, glass, pieces of wire, etc.) should be done with special tools.

3.6.31. During an internal inspection of the tire, between the bead on the inside and the rim edge, it is necessary to put wooden or special spacers.

3.6.32. Tires of mounted wheels should be inflated only through the spool in a special safety device (cage, spider, etc.). At the end of tire inflation, it is necessary to check for bleeding through the spool with a soapy solution from a dropper or from another appropriate device.

3.6.33. When inflating tires, it is necessary to monitor the correct fit of the locking ring, correcting it only at the beginning of inflation.

3.6.34. Tire inflation should be carried out from the pneumatic network of a stationary compressor or cylinder with compressed air having a reducer.

3.6.35. In all cases, tires should be inflated to the pressure established by the rules operation of this type of pneumatic tires and depending on their installation location on the vehicle.

Before inflating a tire, make sure that the hose is securely fastened to the valve of the pneumatic chamber, and during inflation, constantly monitor the pressure in the wheel using the pressure gauge mounted on the hose.

3.6.36. When inflating a pneumatic tire, it is forbidden to knock on it. Correct by tapping only after the air supply has been cut off.

3.6.37. It is possible to inflate a tire without remounting only if the air pressure in it has decreased by no more than 40 percent of normal, or if there is confidence that the decrease in pressure has not violated the correct installation of wheel parts.

3.6.38. The tire of the wheel mounted on the vehicle should be inflated only when the wheel is raised from the ground. After inflating the tire, install the cap on the valve.

3.6.39. Tire assemblies delivered for repair and after repair should be installed in a specially designated place in a standing position and the convex side of the disk away from you towards the wall.

3.6.40. When cutting cuffs on a blank, it is necessary to cut with a knife away from you, moisten the knife with water.

3.6.41. In the event of malfunctions with the chamber valve, reducer, compressed air cylinder valve, tools and devices, it is necessary to stop work and report this to the garage mechanic on duty.

4. SAFETY REQUIREMENTS IN EMERGENCIES

4.1. Actions of the driver in the event of situations that may lead to undesirable consequences

4.1.1. When working on a transport and harvester, the following main emergencies may occur:

collision with another vehicle;

hitting people;

overturning of the transport and harvester, exit from a high platform;

igniting the machine, which could result in a fire or explosion.

4.1.2. In the event of an emergency, the driver is obliged to stop work, turn off the engine, brake the wheels, immediately report the incident to his immediate supervisor and then follow his instructions to prevent accidents or eliminate the emergency.

4.1.3. Drivers who are nearby are obliged to immediately come to the scene and take part in providing first aid to the victim or eliminating the emergency situation that has arisen.

4.1.4. In the event of a fire, it is necessary to immediately begin to eliminate the fire, using primary fire extinguishing equipment and, if necessary, inform the fire brigade personally or through people nearby.

4.1.6. In case of fire of the transport-harvesting machine, only carbon dioxide, powder and aerosol fire extinguishers should be used. When using a carbon dioxide fire extinguisher, do not touch the bell with your hand.

4.1.7. If fuel (gasoline) ignites, it is forbidden to extinguish the fire with water. In this case, you should use a foam fire extinguisher, cover the fire with earth, sand, cover with a tarpaulin or felt mat.

When extinguishing with a felt mat, cover the flame so that the fire from under it does not fall on the extinguishing person.

When extinguishing a flame with sand, a scoop, shovel, etc. do not raise to eye level to avoid getting sand into them.

4.1.8. When using fire extinguishers, direct the jet of foam (powder, carbon dioxide, aerosol) away from people. If foam gets on unprotected areas of the body, wipe it off with a handkerchief or other material and rinse with an aqueous solution of soda.

4.2. Actions of the driver to provide first (pre-medical) aid to the injured

4.2.1. electrical injury

In case of electric shock, first of all, it is necessary to stop the action of the current (turn off the voltage, cut the wire, etc.), while observing safety measures and not touching the victim with bare hands while he is under the influence of current.

In case of electric shock high voltage or lightning victim, despite the absence of signs of life, can be brought back to life. If the victim is not breathing, immediately apply artificial respiration and at the same time heart massage. Artificial respiration and heart massage are done until natural breathing is restored or until the doctor arrives.

After the victim regains consciousness, it is necessary to apply a sterile bandage to the place of the electric burn and take measures to eliminate mechanical damage (bruises, fractures) that may occur during a fall. The victim of an electrical injury, regardless of his state of health and the absence of complaints, should be sent to a medical institution.

4.2.2. Mechanical injury

When receiving a mechanical injury, it is necessary to stop the bleeding, treat the wound with hydrogen peroxide, and apply a bandage. If a tourniquet is applied, it is necessary to record the time of its application. The tourniquet can be left on for two hours in the warm season, and in the cold - one hour.

In case of fractures, it is necessary to apply a splint fixing the immobility of the damaged parts of the body. To do this, you can use boards and a bandage. With open fractures, it is necessary to bandage the wound before applying the splint.

When sprained, apply a pressure bandage and a cold compress to the sprain. In case of dislocations, the limb is immobilized in the position it took after the injury, a cold compress is applied to the joint area.

With all types of mechanical injuries, the victim must be taken to a medical facility.

4.2.3. Thermal burns

For first-degree burns (only redness and slight swelling of the skin are observed), moisten the burned area with a strong solution of potassium permanganate.

For second-degree burns (fluid-filled blisters form), a sterile dressing should be applied to the burnt area. Do not lubricate the burned area with fat and ointments, open or pierce blisters.

In case of severe burns, a sterile dressing should be applied to the burned area and the victim should be immediately sent to a medical facility. Do not lubricate the burnt place with fat or ointments, tear off parts of clothing that are burnt to the skin. The burnt person must be given plenty of hot tea.

4.2.4. Acid and alkali burns

In case of acid burns, the burned area of ​​the body should be washed with water with alkalis added to it: soda, chalk, tooth powder, magnesia. In the absence of alkalis, it is necessary to abundantly water the burnt body with clean water.

In case of burns with caustic alkalis, the burnt area of ​​the body should be washed with water acidified with acetic or citric acid, or washed with clean water, pouring plenty of water on the burned area.

4.2.5. poisoning

In case of poisoning with poor-quality food products, it is necessary to induce artificial vomiting in the victim and rinse the stomach, allowing him to drink a large amount (up to 6-10 glasses) of warm water, tinted with potassium permanganate, or a weak solution of baking soda. After drink milk and give to drink 1 - 2 tablets of activated charcoal.

In case of acid poisoning, it is necessary to thoroughly rinse the stomach with water and give the victim an enveloping agent: milk, raw eggs.

In case of gas poisoning, the victim must be taken out of the room to fresh air or a draft should be arranged in the room by opening windows and doors. When breathing and cardiac activity stop, start artificial respiration and heart massage.

In all cases of poisoning, the victim must be sent to a medical facility.

In case of accidental ingestion of antifreeze, the victim should be immediately taken to a medical facility.

4.2.6. Eye injury

In case of eye injuries with sharp or piercing objects, as well as eye injuries with severe bruises, the victim should be urgently sent to a medical facility. Objects that get into the eyes should not be removed from the eye, so as not to further damage it. Apply a sterile bandage to the eye.

If dust or powder gets into eyes, rinse them with a gentle stream of running water.

In case of chemical burns, it is necessary to open the eyelids and rinse the eyes abundantly for 10-15 minutes with a weak stream of running water, after which the victim should be sent to a medical facility.

In case of eye burns with hot water, steam, eye rinsing is not recommended. The eyes are covered with a sterile bandage and the victim is sent to a medical facility.

5. SAFETY REQUIREMENTS AFTER WORK IS COMPLETED

5.1. Upon completion of work, the driver must:

inspect the machine and make sure it is in good condition;

put the car in the place intended for parking, put the gear lever in neutral position, turn off the ignition, brake the wheels;

lock the cabin door;

remove overalls and other personal protective equipment and put them in the dressing room closet;

wash hands, face and contaminated body parts with soap and water or take a shower.

Contaminated and faulty overalls, if necessary, the driver must hand over for washing, dry cleaning or repair.

5.2. To clean the skin from industrial pollution at the end of the working day, it is necessary to use protective and washing pastes and ointments that combine the properties of protective and detergents.

To keep the skin in good condition after work, various indifferent ointments and creams should be used (boric vaseline, lanolin cream, etc.).

It is not allowed to use kerosene or other toxic petroleum products to clean the skin and personal protective equipment.

5.3. In winter, it is necessary to drain the water from the cooling system. When opening the cap of the engine cooling system, take precautions against the possible release of hot water. Open the cork in gloves or put a pre-dense cloth on the cork to avoid burns to the hands and face.

5.4. At the end of maintenance or repair, tidy up the workplace, clean and put away tools and fixtures.

5.5. Hand over the keys to the security officer at the parking lot.

5.6. It is prohibited to store the transport-harvester at the driver's place of residence.

5.7. About all violations of the technological process, malfunctions and defects noticed during operation, and about the measures taken to eliminate them, the driver of the transport and harvester must inform the garage mechanic or the person responsible for the technical serviceability of the vehicles.

________________________ ________________ _________________

(head position (personal signature) (surname, initials)

divisions

/organizations/ - developer)

AGREED:

Head (specialist)

security services

labor of the enterprise ______________ _______________

Legal Counsel ______________ _______________

(personal signature) (surname, initials)

Chief technologist ______________ _______________

Job description of the driver of the vehicle[name of organization, enterprise, etc.]

This job description has been developed and approved in accordance with the provisions and other regulations governing labor relations in the Russian Federation.

I. General provisions

1.1. The driver of the vehicle belongs to the category of technical performers. He is hired and fired from her by order of the director of the enterprise on the proposal of [fill in the right one].

1.2. The driver of the vehicle reports directly to [fill in as appropriate].

1.3. In its activities, the driver of the vehicle is guided by:

Rules of the road and technical operation of the vehicle;

Regulatory and methodological documents on the issues of the work performed;

Charter of road transport;

the Charter of the enterprise;

Internal labor regulations;

Orders and orders of the immediate supervisor;

This job description.

1.4. The driver of the vehicle must know:

Purpose, device, principle of operation and operation of units, mechanisms and devices of serviced vehicles;

Rules of the road and technical operation of the vehicle;

Causes, methods for detecting and eliminating faults that have arisen during operation;

The procedure for maintenance and the rules for storing the vehicle in garages and open parking lots;

Rules for the operation of batteries and car tires;

Rules for running in new cars and after major repairs;

Rules for the transportation of perishable and dangerous goods;

The influence of weather conditions on the safety of driving a vehicle;

Ways to prevent traffic accidents;

Device of radio installation and composters;

Rules for the supply of buses for boarding and disembarking passengers;

The procedure for emergency evacuation of passengers in case of traffic accidents;

Rules for filling out primary documents for accounting for the operation of serviced transport;

Volumes, frequency and basic rules for performing maintenance work on vehicles;

Ways to increase the overhaul runs of vehicles;

Features of the organization of maintenance and repair of transport in the field;

Ways to increase tire mileage and battery life;

Rules for the use of radio communications in transport;

Features of the organization of intercity transportation.

1.5. During the absence of the driver of the vehicle (vacation, illness, business trip, etc.), his duties are performed by a deputy appointed in the prescribed manner, who is fully responsible for their proper performance.

II. Functions

The following functions are assigned to the driver of the vehicle:

2.1. Driving cars, trucks and other vehicles (driving lifting mechanism dump truck, truck crane crane unit, tanker truck pumping unit, refrigerator refrigeration unit, sweepers and other equipment of specialized vehicles).

2.3. Checking the technical condition of transport.

2.4. Preparation of travel documents.

III. Job Responsibilities

To perform the functions assigned to him, the driver of the vehicle must:

3.1. Drive cars of all types, trucks (road trains) of all types with a carrying capacity of up to 10 tons (over 10 to 40 tons), road trains - according to the total carrying capacity of the car and trailer, buses with an overall length of up to 7 meters (7-12 meters), as well as on driving cars equipped with special sound and light signals, giving the right to an advantage when driving on the roads. Control of the lifting mechanism of a dump truck, crane installation of a truck crane, pumping installation of a tank truck, refrigeration unit of a refrigerator, sweepers and other equipment of specialized vehicles.

3.2. Refuel vehicles with fuel, lubricants and coolant.

3.3. Check the technical condition and receive the vehicle before leaving the line, hand it over and put it in the allotted place upon returning to the fleet.

3.4. Carry out the supply of vehicles for loading and unloading cargo and control the loading, placement and securing of cargo in the car body.

3.5. Eliminate operational malfunctions of the serviced transport that have arisen during work on the line, which do not require disassembly of the mechanisms.

3.6. Announce stopping points and the procedure for paying for travel using a radio installation, install composters, sell subscription books at stopping points.

3.7. Prepare travel documents.

3.8. Perform adjustment work in the field in the absence of technical assistance.

IV. The rights

The driver of the vehicle has the right:

4.1. Get acquainted with the draft decisions of the management of the enterprise relating to its activities.

4.2. Submit proposals for improvement of the work related to the responsibilities provided for in this instruction for consideration by the management.

4.3. Receive from the heads of structural divisions, specialists information and documents on issues within its competence.

4.4. Require the management of the enterprise to assist in the performance of their duties and rights.

V. Responsibility

[Enter as appropriate] is responsible for:

5.1. For failure to perform (improper performance) of their official duties provided for by this job description, to the extent determined by the labor legislation of the Russian Federation.

5.2. For offenses committed in the course of carrying out their activities - within the limits determined by the administrative, criminal and civil legislation of the Russian Federation.

5.3. For causing material damage - within the limits determined by the labor, criminal and civil legislation of the Russian Federation.

The job description was developed in accordance with [name, number and date of the document].

Head of structural unit

[initials, last name]

[signature]

[day month Year]

Agreed:

Head of the legal department

[initials, last name]

[signature]

[day month Year]

Familiarized with the instructions:

[initials, last name]

[signature]

[day month Year]

\Typical job description of the Driver of the transport and harvesting machine

Job description of the Driver of the transport and harvesting machine

Position: Truck driver
Subdivision: _________________________

1. General Provisions:

Subordination:
• The driver of the transport and harvesting machine is directly subordinated to ..........................................
• The driver of the transport-harvesting machine follows the instructions .............................................. .........

(instructions of these employees are carried out only if they do not contradict the instructions of the immediate supervisor).

Substitution:

• The driver of the transport and harvesting machine replaces .............................................. ................................................
• The driver of the transport and harvesting machine is replaced by .............................................. ...................................

Recruitment and dismissal:
The driver of the transport and harvesting machine is appointed to the position and dismissed by the head of the department in agreement with the head of the unit.

2. Qualification requirements:

Must know:

• device and rules for servicing transport harvesters
• fuels and lubricants
• purpose, timing and methods of charging batteries
• traffic rules, traffic rules on the territory of the enterprise, station tracks
• installed alarm.

3. Job Responsibilities:

• Control of transport and harvesting machines of various systems and carrying capacities when transporting cargo and garbage from the forecourt and station areas, platforms and passenger platforms, streets, etc.
• Supervision of loading and unloading.
• Maintenance and upkeep of the harvester.

p. 1 Job description Transport and harvester driver
p. 2 Job description Transport and harvester driver

4. Rights

• The driver of the transport and harvesting machine has the right to give instructions to his subordinate employees, tasks on a range of issues included in his functional duties.
• The driver of the transport and harvesting machine has the right to control the fulfillment of production tasks, the timely execution of individual orders by employees subordinate to him.
• The driver of the transport and harvesting machine has the right to request and receive necessary materials and documents related to the issues of its activities and the activities of employees subordinate to it.
• The driver of the transport and harvesting machine has the right to interact with other services of the enterprise on production and other issues that are part of his functional duties.
• The driver of the transport and harvesting machine has the right to get acquainted with the draft decisions of the enterprise's management regarding the activities of the Division.
• The driver of the transport and harvesting machine has the right to propose for consideration by the manager proposals for improving the work related to the duties provided for in this Job Description.
• The driver of the transport and harvesting machine has the right to submit proposals for the consideration of the head of the proposal to encourage distinguished employees, to impose penalties on violators of production and labor discipline.
• The driver of the transport and harvesting machine has the right to report to the manager on all identified violations and shortcomings in connection with the work performed.

5. Responsibility

• The driver of the transport and harvesting machine is responsible for improper performance or non-performance of his duties stipulated by this job description - to the extent determined by the labor legislation of the Russian Federation.
• The driver of the transport and harvesting machine is responsible for violating the rules and regulations governing the activities of the enterprise.
• When transferring to another job or dismissal from the post, the Driver of the transport and harvesting machine is responsible for the proper and timely delivery of cases to the person taking up this position, and in the absence of such, to the person replacing him or directly to his manager.
• The driver of a transport and harvesting machine is liable for offenses committed in the course of carrying out his activities - within the limits determined by the current administrative, criminal and civil legislation of the Russian Federation.
• The driver of the transport and harvesting machine is responsible for causing material damage - within the limits determined by the current labor and civil legislation of the Russian Federation.
• The driver of the transport-harvesting machine is responsible for compliance with the current instructions, orders and orders for the preservation of trade secrets and confidential information.
• The driver of the transport and harvesting machine is responsible for compliance with the internal regulations, safety and fire safety rules.

This job description was developed in accordance with (name, number and date of the document)

Head of structural

The job description of a car driver regulates working relationships. It determines the order of subordination of an employee, the rules for employment and dismissal of him from his post, the requirements for education, knowledge, and skills. The document contains a list of rights, functional duties, types of responsibility of the driver.

The document is prepared by the head of the department of the organization. Approved by the director of the institution.

The standard form provided below can be used when compiling a job description for a truck driver, passenger car, bus, personal, personal driver, freight forwarder, etc. A number of provisions of the document may differ depending on the specialization of the employee.

Sample job description for a car driver

I. General provisions

1. The driver of the car belongs to the category of "technical performers".

2. The driver of the car reports directly to the head of the structural unit / general director.

3. During the absence of the driver of the car, his functional duties, responsibility, rights are assigned to another official, as reported in the order of the institution.

4. A person who has the rights of category "B" / "C" / "D" and a driving experience of at least two years is appointed to the position of a car driver.

5. The appointment and dismissal of the driver of the car is carried out by order of the general director of the institution.

6. The driver of the car is guided in his activities:

• this job description;
• internal labor regulations;
• the charter of the institution;
• orders of the immediate superior;
• legislative acts of the Russian Federation;
• methodological materials for conducting activities;
• orders, orders of management;
• governing, normative acts of the institution.

7. The driver of the car must know:

• general arrangement of the car;
• the main technical characteristics of the units, device, purpose, principle of operation, maintenance of mechanisms, vehicle devices;
• causes, methods for identifying, eliminating vehicle malfunctions, their consequences;
• traffic rules, penalties for their violation;
• rules for the implementation of vehicle maintenance;
• resolutions, legislation, orders, instructions, other normative acts of the institution;
• car maintenance standards, maintenance of the interior, body, keeping them in a clean, comfortable condition.

II. Responsibilities of a car driver

The driver of the car performs the following duties:

1. Contributes to the technically sound condition of the car entrusted to him.

2. Timely delivers the car to a predetermined place.

3. Drives a car, ensuring maximum safety for the health, life of passengers and other road users.

4. Contributes to the safety of the car, the property located in it.

5. Leaves the car in the parking lot with the alarm on.

6. Blocks all car doors while driving, parking.

7. Monitors the technical condition of the mechanisms, assemblies of the car.

8. Independently performs the necessary work to ensure the safe operation of the car, according to the instructions.

9. Keeps units, mechanisms, car interior clean. Treats them with the intended care products.

10. Regular maintenance and repair of the car in the service center.

11. Do not use substances that reduce attention, reaction speed, performance.

12. Enters information into the transport lists: routes, distances covered, consumption of fuels and lubricants.

13. Studying the features of the route before leaving. Discusses it with your immediate supervisor.

14. Fulfills the instructions of the immediate superior.

15. Leaves the car entrusted to him in a guarded parking lot or garage after the end of the working day.

16. Contributes to the reduction of unproductive costs for the maintenance of the car.

17. Carefully and rationally uses the materials and equipment entrusted to him.

18. Provides established documentation within a specified time frame.

19. Contributes to the reduction of transport downtime, irrational use of motor vehicle resources.

III. The rights

The driver of the car has the right:

1. Propose changes to traffic routes.

2. Independently make decisions within their own competence.

3. Receive information from contractors about the progress of car repairs or maintenance.

4. Get advice from experts on issues that are beyond the competence of the driver of the car.

5. Do not perform functional duties in the event of a danger to health, life.

6. Report to the management about the identified shortcomings in the activities of the institution, send proposals for their elimination.

7. Demand from the management the formation of normal conditions for safe work, the performance of their duties.

8. Put forward proposals to the management to improve the activities of the institution.

9. Communicate with departments of the institution regarding their activities.

10. Receive information from managers about projects in relation to their activities.

11. Participate in educational events, improve your own skills.

IV. Responsibility

The driver of the vehicle is responsible for:

1. Safety, performance of the car entrusted to him, its components and mechanisms.

2. Violation of the provisions of the governing documents of the institution.

3. Improper performance of their official duties.

4. Causing damage to the institution, its employees, customers, the state, road users.

5. Reliability of information in the documentation sent to management.

6. Violation of the provisions of labor discipline, internal labor regulations, fire protection standards, safety regulations.

7. Consequences of independent actions, own decisions.

8. Reliability of data on technical condition car entrusted to him.

9. Untimely direction of the car to service maintenance and repair.

truck driver

Driver truck drives a vehicle that belongs to the relevant category. It tows trailers of the specified weight and dimensions.

Specific duties of a truck driver:

1. Compliance with the rules for submitting vehicles for loading and unloading.

2. Checking the conformity of the stowage, fastening of the cargo on the car with the requirements for ensuring the safety of the cargo and traffic safety, the car.

3. Monitoring compliance with the rules for carrying out loading and unloading operations, transport loading standards.

Bus driver

The bus driver transports passengers, observes their safety while driving, boarding, disembarking from the passenger compartment.

Specific duties of a bus driver:

1. Passing medical examinations in the prescribed manner.

2. Compliance with the timetable and route.

3. Message to passengers about the start and end of boarding.

Forwarding driver

The forwarding driver delivers goods, material values, primary documentation to the designated places. It is entrusted with the function of transferring funds.

Specific functional duties of a forwarding driver:

1. Receipt of goods from warehouses in accordance with the content of the accompanying documents.

2. Checking the packaging of goods, monitoring the correctness of the loading and unloading operations, the location, stowage of goods in the car.

3. Ensuring the safety of inventory items during transportation.

4. Registration of documentation on the acceptance, delivery of goods.

The driver-forwarding agent acts as a trustee of the organization in established cases.