A well-chosen set and wheel size for an energetic Ford Focus car will give it not only additional beauty and aesthetics, but also improve dynamic performance. Each owner passenger car Focus has the ability to purchase alloy wheels with the same diameter, rim and offset as the standard wheels installed at the factory.

You can also make a small restyling and install more wide wheels with the smallest overhang. As a result, Ford will look more original and slightly increase its dynamic performance and stability on the track.

There is almost always Alternative option replacement of a standard wheel and disk with analogs with large sizes rims. Ideally, after that while riding on vehicle there shouldn't be any problems.

More massive wheels as a result "require" the use of wide tires, and they contribute not only to improving dynamic performance, but also to a high level of braking, respectively, the driver can feel calm even with aggressive driving.

The car owner must independently make a choice in favor of certain wheel sizes. Immediately before choosing and installing, you must carefully study the main parameters recommended by the car manufacturer:

• rims;
• bolt pattern;
• departure;
• wheel size.

The specified parameters must correspond to the characteristics of the vehicle. If certain problems arise when installing wheels with non-standard parameters, then it is better to contact experienced maintenance specialists for help.

Detailed specifications of wheel, tire and rim sizes for the Focus 1 and 2 model

Based on ET overall departures for rims Ford, maximum deviation from standard size should not exceed +/-5 mm.

The disk size implies the optimal width of the product in relation to the tire no more than 20-30%. As a rule, tuning enthusiasts and ordinary drivers do not always pay special attention for these indicators.

Many manufacturers began to produce various non-standard rims, regardless of the width and height parameters. In addition, with proper use of a wider disc, handling performance will improve.

But only if tires and wheels with identical dimensions are used. For example, tires with a width of 185 mm are perfectly combined with rims 205 7J, 205 6J, 195 6J.

On Russian Ford Focus configurations, factory tires with a high profile were installed as standard, in contrast to identical models produced in foreign factories.

This allows you to install any tires, according to the specified instructions from the manufacturer, depending on the wishes and block control settings.

Factory specifications from Ford:

1. the total number of bolts for installing the wheel is 4;
2. central diameter of fasteners -108 mm; in the designation 4/108;
3. the dimensions of the diametrical holes for landing the wheel under the hub are 63.3 mm, d63.3 is indicated.

If you use holes with smaller diameters, then the wheel cannot be installed on the hub. For diametrical holes with large values, it is necessary to use special adapter rings.

Standard disc sizes

As for the question of whether the fender liner will not cling, here it is necessary to observe the optimally recommended wheel parameters and install tires with a lower profile.

For example, 205/50/R16 tires can be used, but they do not guarantee uniform quiet ride- problems may arise at the moment of hooking the fender liner.

It is best to use 195/65/R15 tires as the wheels are slightly taller with them, which improves handling performance.

The most popular and popular tire sizes for Ford Focus 1 and 2:

• 195/65/R15;
• 185/70/R14;
• 205/50/R16;
• 185/65/R14;
• 195/55/R15.

If we are talking about ET indicators, then for cast and stamped wheels they are completely different. A lower overhang value indicates a wider track.

Also note that the locks and nuts for factory auto disks have a difference. The main thing is the design and form. The conical corners of the working areas are adjacent to the working disk surface. Nuts on stampings have a smaller angle and, accordingly, do not adhere so strongly to the product.

Therefore, experienced specialists do not recommend using stamping nuts as fasteners on castings. Too small area of ​​contact with the work surface, which means poor fastening for the auto disk. It is also necessary to take into account the fact that each tightening of the nut will gradually correct contact with the working surface.

To check the coupling of a new disc to the calipers, the following procedures must be performed:

1. install it on the valve;
2. fasten the nuts to the hub;
3. fully spin the disk.

Wheel bolt pattern Ford Focus 2, 3

Example: wheel bolt pattern on Ford Focus cars with parameters 5/108. Many car lovers may have problems with the designation of these numbers. Therefore, we indicate their decoding in more detail:

1. the number 5 indicates the total number of diametrical holes for wheel fasteners;
2. the number 108 indicates the size of the diameter of these holes.

Disk offset on Focus 2 and 3 models:

1. the standard size is 52.5mm;
2. wheel offset on reystayling is 50 mm.

For beginners, departure is a rather complicated and difficult concept. If to speak in simple words, then disc reach indicates the total distance from the middle of the product to the main area of ​​the fasteners located on the hub.

• R15/195/65;
• R16/205/55.

The letter R stands for the radius of the wheel.

Wheel bolt pattern for Focus 3

The general parameters of the 3rd generation of the Focus are practically the same as similar models 5/108.

Wheels for 3rd Edition Ford Focus

The third release of the famous Focus model was implemented in 2010. The car was presented at the famous salon in Detroit. The vehicle was presented in several bodies: sedan, station wagon and hatchback.

It is known that Ford Focus is still one of the most sought after cars in the world. Sales are growing every year, and fans of this car are satisfied with its ease of operation and stylish design.

The American manufacturer achieved such results due to the high ratio between quality and cost.

In addition, the 3rd edition of the cars was made in kinetic design. Many admired the originality and uniqueness of this car. On the track, the Focus demonstrates excellent performance and indicators of control, acceleration and stable ride.

Good handling on the vehicle is achieved through an improved balance between rims and tires. Therefore, it is necessary to consider the main type of rubber and wheel parameters for optimal driving on the Focus 3.

Optimal wheel sizes

Each car produced by the American Ford line has certain wheel and tire sizes recommended by the manufacturers. Consider the main parameters necessary for good car handling:

1. Disc sizes: 16, 17 and 18 inches;
2. Tires 235/40/R18, 215/50R17, 205/55R16;
3. Disc width ET50, ET55.

Absolutely for everyone wheel sizes fasteners 5/108 with a central diametrical hole of 63.3 mm and a stud of 14.5 mm are used.

Taking into account the main indicators, everyone will be able to decide on the choice of a wheel for the Focus 3 model. As the best option recommends using original factory products or similar products from famous brands.

Branded models are more durable and reliable, since they are specially produced for a particular Focus model. This is a very important factor, even in a situation where the car runs into a deep hole or crack.

As a result, the wheel product is not deformed, and the driver continues to control the control of the vehicle.

Discs are selected according to the width of the tire, they must be identical. In most cases, an American company produces original factory stamps for Focus 3. Such discs are excellently used in difficult conditions and are of low cost.

In addition, when purchasing such wheels, you don’t have to worry about the size, since they automatically fit the standard Focus 3 wheels.

Subject to competent recommendations, a car lover should have no problems choosing a wheel size for a Ford Focus car. If desired, you can use non-standard models, but it will be necessary to slightly change the technical components of the vehicle.

What bolt pattern is used on Ford Focus cars? We often hear this question from owners of American brand cars. In this article, we will consider the characteristics of disks and bolt patterns for three generations of this car. Wheel disks- a must-have attribute of any car, and it gives it a more stylish design, as well as modern, which emphasizes the individual views of the owner. The manufacturer does not always complete the car with something elegant, so car owners sometimes have to go to additional expenses to sharpen appearance cars according to your needs and interests. However, it must be remembered that any change made to the car, including the replacement of disks, must be accompanied by thorough technical preparation, because the safety of the driver and his passengers depends on this.

If you, as a car owner, have decided to install new rims on a Ford Focus car, then you need to know one important parameter, without which this procedure simply cannot be carried out properly.

Razboltovka Ford Focus- this is the ratio of the number of bolts for fastening the disk to the diameter of the circle on which the bolts are located. As a rule, it is considered that the ratio of 5/112 is normal and safe. The first number indicates the number of mounting bolts, and the second, respectively, the diameter of the very circle on which they are placed. The second parameter (PCD) is standardized for each vehicle and complies with international recommendations (see figure).

Before considering which bolt pattern is used on Focus cars different generations, we offer to refresh your knowledge in the characteristics and sizes of rims. Surely you know that the disk is characterized by such parameters as:

1. Rim width(B) is a parameter that characterizes the diameter of the annular circle, which describes the inside of the rim. In fact, its presence provides support for the tire. As a rule, for self-measurement of this indicator, it is used simple procedure, you just need to subtract 20% of the distance from your tread width and get the rim width.

2. Departure(ET) - a parameter that equals the distance from the middle of the width of the fit of the rim to the wheel adjacent to the automobile hub.

Razboltovka Ford Focus 1

The world saw the first generation Ford Focus back in 1998. The plant produced several modifications and configurations, so the wheels were different sizes. For the entire period of production, disks of the following sizes were offered:

- 14 inches;
- 15 inches;
- 16 inches.

Based on these data, different tires are used and only certain wheels are suitable for them. In almost all cases, the following rubber sizes are installed:

1. Radius 14 = 185/65;
2. Radius 15 = 195/60;
3. Radius 16 = 205/50.

Ford Focus 1 It has following sizes discs and bolt pattern:

Disc width – 5.5, 6.0, 6.5, 7.0
Departure– ET 38-52
Razboltovka- 5x108
Centering hole – 63,3.

Razboltovka Ford Focus 2

The second generation Ford Focus was produced from 2004 to 2011. This car became very popular in the Russian Federation and earned the respect of car owners. The manufacturer produced cars with the following wheel options:

- 15 inches;
- 16 inches;
- 17 inches;
- 18 inches.

Ford Focus 2 has the following disk parameters and bolt pattern:

Disc width– 6.0, 6.5, 7.0 and 8.5
Departure– ET 45-52.5
Razboltovka- 5x108
Centering hole – 63,3

car manufacturer Ford Focus 2 recommends installing the following wheels:

Tires 195/65-R15 6JR15 5x108 ET52.5 DIA 63.3;
6.5JR16 5×108 ET52.5 DIA 63.3 for 205/55-R16 rubber

Razboltovka Ford Focus 3

latest generation Ford Focus 3- This is a car that has been produced since the beginning of 2011, and to this day. As well as the second generation, he won universal recognition and popularity in our country. leaving the factory this machine Equipped with 16" wheels. The ST version is produced with wheel size 18.

Choosing the right Ford Focus 3 wheel size is easy. The factory settings correspond to only one size per 16 inches, so there should be no problems with the choice. The car was produced in sedan, hatchback and station wagon bodies. It was completed with both cast light-alloy products and steel, produced by stamping. Tires and wheels for the "Focus" in the third generation, it is important to choose the right and high quality. Auto has long history, for 20 years now Ford company produces this popular model. The fourth generation has recently been introduced.

Produced since 2011, the third generation of the car has gained very great popularity in Russia. In 2018, it was replaced by a newer, fourth generation, which embodied all the qualities of its predecessor and acquired many new ones.

Winter tires on Ford Focus 3

To date, a very wide range of products for the car is presented on the shelves of car dealerships. This also applies to the wheels on the "Focus 3", which are limited by the manufacturer to only one size - 16 inches.

The owners of this popular car, like any other, also face the need to change tires before the onset of a certain season. In this case, you have to choose from a variety of products presented in stores. It can be both very famous and expensive brands, and cheaper models.

The choice of brand and properties of rubber depends only on the personal preferences of the motorist.

It is worth remembering that even products are very expensive manufacturers can be absolutely useless if used and stored improperly. It is very important to select products only with the correct dimensions and constantly monitor their condition. This also applies to the setting of tire pressure, which is regulated by the manufacturer and indicated in the technical documentation.

The country's market is rich in offers for the sale of rubber in various designs and having different characteristics that will suit even the most demanding car owners. This is due to the great popularity of the car.

It is also worth noting that from right choice tires will affect the safety of the driver and passengers.

In difficult weather conditions, on slippery surfaces from installed rubber often depends on people's lives. In addition, tires have a huge impact on undercarriage wear, handling, dynamic characteristics and other qualities.

Wheels with a dimension of 16 inches on the "Focus"

How to choose

For a quality selection of tires for a Ford Focus 3 car, you need to know what the main differences are and what they are.

By seasonality, tires are:

• Summer. They can only be operated starting from a temperature of five degrees Celsius. The tread pattern of such tires is not very pronounced, compared to winter ones. By operating summer products at elevated temperatures, they become harder and cool themselves. Suitable for riding high speeds on good roads.
• Winter. Can only be used in winter period, With temperature regime below zero degrees Celsius. The tread of such tires is much deeper than that of summer counterparts. At cold temperatures, the rubber heats up on its own and increases its own elasticity. As a result, road grip is increased. This makes the car more manageable, reduces the braking distance and enhances the driving dynamics. Life time winter tires usually more than summer, because the average speed is less.
• All season. Often there is a name - "universal". They are the middle link between winter and summer. Manufacturers indicate that this type of rubber can be used regardless of the season. However, professionals recommend installing this type only when the outside temperature is between -5 and +7 degrees Celsius. In fact, universal tires are inferior to winter tires in the cold season and summer tires in the warm season. Therefore, it is popular in countries with a relatively warm climate and dry winters. It is forbidden to operate them in very hot and very cold weather.

To install new wheels on a Ford Focus car, you need to know the bolt pattern of this model. Discs have to be changed frequently. Some owners are not satisfied with the design, others with the degree of wear, and still others with the dimensions. And if any of these cases apply to you, urgently arm yourself with paper and a pen - there will be a lot of technical information.

Disk bolt pattern: what is it?

Recall that the concept of "bolt pattern" means the ratio of the number of mounting bolts to the diameter of the circle on which they are located. The safe ratio is 5/112. In this proportion, the first number reflects the number of bolts, the second - the diameter of the circle.

The diameter of the circle on which the bolt points are placed is designated PCD and is a standard value that meets international criteria. Any change in the car must take into account the parameters of safety and reliability when driving, so we will consider all valid Ford Focus bolt patterns. On Focuses of three generations, the bolt pattern is almost the same, although there are small but important differences.

The model receives so much attention due to its high popularity in Russia since the appearance of the second Generation Focus in 2005. After 5 years, this model earned the title of the most popular car of the year. So american cars are still in demand, and the bolt pattern of all three Ford Focus variations is made by most serious service stations. Moreover, replacing disks is an affordable, simple and bright way to make tuning and stand out on the road.

Wheel bolt pattern for Ford Focus 1

Ford Focus 1 - base model in the lineup, produced longer than the others and still perfectly behaving on the road. The manufacturer released the first generation in the last century, in 1998. Ford Focus 1 celebrates its 20th anniversary this year. Initially produced various modifications with configuration options to choose from, therefore, wheels for cars of this model fit three sizes:

• 14 inches;
• 15 inches;
• 16 inches.

The choice of tires also depends on the size of the wheels. Many people like to install bigger tires, hoping for an improvement. driving performance. But to win in speed with this approach will not work, especially if the driving is not too experienced driver. Tires on the Ford Focus 1 are also installed in three different sizes:

• 14/185/65;
• 15/195/60;
• 16/205/50.

Based on these indicators, we obtain the characteristics of the discs for bolt pattern. Permissible disc width: 5.5, 6.0, 6.5, 7.0. Departure is marked ET 38-52. The bolt pattern is 5x108, where 5 is the number of holes for the bolts for attaching the wheels, and 108 is the diameter of their location. The size of the centering holes for the hub is 63.3.

Wheel bolt pattern for Ford Focus 2

The second generation of Focuses, just like the first, has already been discontinued. The popular Ford Focus 2 model was launched in 2004 and ended in 2011. However, there are still many such cars on the roads. Most of them require repair and updating.

The second model has four modification options, respectively, they need wheels of the following sizes:

• 15 inches;
• 16 inches;
• 17 inches;
• 18 inches.

• 15/195/65;
• 16/205/55;
• 17/205/50;
• 18/225/40.

According to the bolt pattern, the second model differs little from the first one and must correspond to the following parameters: 5x108 with an offset of ET 45-52.5. The size centering hole 63.3, rim width 6.0, 6.5, 7.0, 8.5. Experienced car owners note that a deviation of 5 mm in one direction or another, which does not affect the quality of fastening, is permissible along the outreach. When choosing wheels for tires, be guided by the fact that the width of the disk is about 20-30 percent less than the width of the rubber. With wider discs, the car's handling improves.

Wheel bolt pattern for Ford Focus 3

The easiest way to service car models that appeared on the market a few years ago: the production and supply of spare parts have already been established, identified weak spots models and found ways to solve any problems. The third modification in the Focus line is still being produced, as interest in it is consistently kept at a high level. Ford Focus 3 was launched in 2011, appeared in Russia the same year and continues to be produced in several versions. The main part comes with 16-inch wheels, while the ST version is equipped with 18-inch wheels.

Accordingly, tires of 2 sizes are installed on the Ford Focus 3:

• 16/205/55;
• 16/215/55.

The bolt pattern is 5x108, the centering hole is 63.3, the offset is ET 50, the width is 7. Ford has long been domestically assembled, tires with more high tread. In this case, it is recommended to strictly follow the instructions of the developer. Read the operating instructions, which indicate the dimensions of all replacement parts, the characteristics of consumables, tires, wheels, as well as the terms and conditions for their replacement.

Rice - "Drawing rim Ford Focus Sedan"

Conclusion

Three generations of Ford Focus were produced with the same bolt pattern, but with a huge number of tire and rim options. Each model has its own version, however, you can pick up interchangeable wheels on the model different years release. As a rule, it is possible to find your own size, since the choice of tires on the market is extremely wide.

On the Ford Focus of all 3 modifications, details are important: screws, nuts, washers. ET value for stamped and alloy wheels differs, while the wider the track, the smaller the overhang value. The nuts of both types of disks differ in taper - on stamped ones it is lower. It is not worth changing the nuts, otherwise the reliability of fastening will be violated.