Ulyanovsk cars car factory won the respect of motorists across the country, thanks to their exceptional reliability. But breakdowns and damage cannot be avoided, and UAZs are no exception. In order for your car to be always on the go, it needs quality service, and sometimes repairs. It is better to entrust them to qualified specialists!

Choose your UAZ:

Autocentre "TORGMASH" offers private and legal entities undergo periodic maintenance of UAZ at its base. All work is carried out on a specially prepared site, equipped with the most modern equipment and diagnostic equipment.

Timely maintenance of cars of the UAZ family will allow you to avoid unexpected breakdowns and significantly extend the life of the vehicle components and assemblies.

When to do maintenance

Maintenance UAZ is necessary if:

• The next deadlines came up - mileage, engine hours, time for changing oils and coolant.
• Revealed extraneous knocks, vibrations and noises during operation.
• Violated adjustment of components and assemblies - malfunctions are eliminated when servicing the car.

Service types

UAZ daily maintenance:

• visual inspection of the condition of the platform and body, glass, paint, license plates, etc.;
• checking spare parts and accessories;
• checking the tightness of all systems containing fuel, oil and coolants for leakage;
• assessment of the state of electrics, lighting devices and alarm systems;
• filling the glass washer reservoir special fluid or water (only in the warm season);
• steering wheel travel check;
• control of serviceability of brakes;
• cleaning or replacing the air filter;
• elimination of all identified defects;
• car wash.

• clutch pedal free travel adjustment;
• checking the free play of the steering wheel, clearances in the steering rod joints, in the pivot joints;
• checking the splint of the nuts of the ball pins, the fastening of the lever knuckle, ball pins, ball bearings to the casings of the axle shafts, steering bipod, tightening the nuts for fastening the tips;
• setting the free and working strokes of the brake pedal;
• assessment of the fastening of the exhaust pipe of the muffler and its suspension;
• checking the fastening of the wheels, the condition of the tires and the air pressure in them;
• checking the fastening of the control drives of the gearbox, transfer case;
• checking the fastening of the front and rear flanges cardan shafts to shaft flanges transfer box;
• cleaning the battery from dirt;
• cleaning the battery vents in traffic jams;
• checking the electrolyte level and, if necessary, topping up with distilled water;
• checking the tension of the fan belt and the fastening of the generator;
• fulfillment of all the instructions of the lubrication table provided for TO-1.

During TO-2, you should:

• check the operation of the clutch and the free travel of the clutch pedal;
• check and, if necessary, adjust the gaps between the rocker arms and valves;
• check the fastening of the engine, engine oil sump, upper and lower parts of the clutch housing;
• check the fastening of the radiator and its lining, blinds, expansion rods;
• during the inspection, check the tightness of the cooling system, the serviceability and fastening of the cooling system pump and fan, the condition of the fan belt;
• clean the generator and starter from dirt and oil and check the condition of the collector and starter brushes;
• blow out the cavity of the generator and starter compressed air and check their fastening;
• adjust fan belt tension;
• check the fastening of the inlet and outlet pipelines;
• clean the surface of the spark plugs, the ignition coil of the sensor-distributor and wires high voltage from dirt and oil;
• check the condition of the high and low voltage wires;
• remove the spark plugs and check their condition;
• clean the electrodes and adjust the gap between them;
• check the degree of charge of the battery by the voltage of the cells under load;
• remove the battery for recharging;
• check the fastening of the battery in the socket;
• check the carburetor mounting and fuel pump, troubleshoot if found;
• adjust the speed crankshaft on the Idling;
• check the fastening of the crankcase and bipod of the steering mechanism;
• check and, if necessary, adjust the engagement of the worm and the steering roller;
• check the amount of convergence of the front wheels, adjust if necessary;
• check drive operation and operation parking brake;
• if necessary, remove the drum, check the wear of the brake linings, disassemble, wash and lubricate the expansion and adjustment mechanisms;
• check the condition of the frame, springs, spring pads, cups, clamps and shock absorbers by inspection, if necessary, eliminate faults. Loose rivets of cups and collars of springs should be re-riveted;
• check and, if necessary, adjust the wheel bearings;
• remove the brake drums and clean the brakes. Check the condition of the brake drums, shoes, linings and fastening of the brake shields;
• check the condition of pipelines brake system and brake cylinders;
• install the brake drums and adjust the gaps between brake drums and pads;
• check the fastening of the leading flanges of the hubs and flanges of the axle shafts;
• check the fastening of the bearing caps of the drive gears of the front and rear axles;
• check the fastening of the gearbox on the clutch housing and transfer case on the gearbox;
• check the clearances in the bearings of the final drive gear of the front and rear axles and, if any, eliminate defects;
• check the fastening of the cardan shaft flanges;
• check the fastening of the body (cabin) and platform to the frame;
• check and, if necessary, adjust the tension of the cables of the front door windows;
• check the fastening of the fuel tanks;
• if necessary, balance the wheels;
• clean the hoses and wash the parts of the closed crankcase ventilation system with kerosene;
• clear air filter and its filter element from dust and dirt;
• wash the flame arrester mesh inside the filter cover with kerosene;
• replace each filter element with a new one;
• Follow all instructions in the lubrication table.

Seasonal Service

Seasonal Service is held twice a year - in spring and autumn, and, if possible, is combined with the next TO-2. When switching to the winter or summer season of operation, the scope of work on TO-2 is supplemented by the following operations.

1. Before the summer season of operation:

• put the damper for heating the working mixture of the gas pipeline to the "Summer" position;
• drain sediment from fuel tanks;
• remove the heater and wiper motors, check the condition of the collector and brushes, rinse and lubricate the bearings;
• flush the cooling system;
• replace the oils in the units with summer grades provided for in the lubrication table.

2. Before winter season operation:

• set the damper for heating the working mixture of the gas pipeline to the “Winter” position;
• Rinse fuel tanks and fuel filters;
• replace the oils in the units with winter grades provided for in the lubrication table;
• prepare the starting engine heater for operation (when installing it);
• check the operation of the heating and ventilation system of the body (cabin);
• check the operation of the blinds, troubleshoot and lubricate the traction;
• clean or replace the air filter vacuum booster brakes.

Remember that during the maintenance of the UAZ, all previous types of maintenance must be included in it!

If you need to carry out maintenance of a UAZ car in Moscow, you should not contact third-party organizations various forms property. You can successfully resolve the difficulty that has arisen in the TORGMASH auto centers. High quality provision of services, use of the most modern technologies and acceptable cost - these are the 3 main components of the success of our company.

UAZ maintenance It is designed to keep the car in working condition, reduce the intensity of wear of parts, prevent the occurrence of malfunctions and identify them for timely elimination. Compliance with the frequency and quality performance of maintenance in the prescribed scope ensure the constant technical readiness of the car and reduce the need for repairs. If a malfunction of the mechanisms, extraneous noise, knocks or vibrations, as well as violations of adjustments and other malfunctions are detected, the driver is obliged to immediately take measures to eliminate them, regardless of the period of the next maintenance. TO UAZ be carried out at maintenance points or sites or in specially equipped rooms that provide the service personnel with the necessary conditions for work. The lack of the necessary equipment and complex stationary or mobile maintenance facilities is not a basis for changing the volume, frequency and conditions of car maintenance.

The scope of maintenance includes control and diagnostic, fixing, lubricating, adjusting, electrical and other work performed without disassembling the units and removing individual nodes from the car.
Maintenance according to the frequency, volume and labor intensity of the work performed is divided into the following types:

For maintenance of a new car and work after a break-in, see the section "Maintenance and break-in of a new car" .

The frequency of carrying out TO-1 and TO-2 is given in accordance with GOST 21624-81.

Operating environment category	Periodicity of maintenance, km
	TO-1	TO-2
I	4000	16000
II	3600	14000
III	3200	12000
IV	2800	11200
V	2400	9600

1. Visually check the completeness of the car, the condition of the body (cabin) and platform, windows, rear-view mirrors, plumage, license plates, paint, door locks, frame, springs, shock absorbers, wheels and tires.
   Inspect the parking area and make sure that there are no leaks of fuel, oil, cooling and brake fluid.
   Eliminate the detected malfunctions, bring the amount of coolant, oil, fuel and brake fluid to normal.
2. Check the operation of lighting devices, light and sound alarms, wipers.
3. Check the free play of the steering wheel and the condition of the brakes.
4. Check the oil level in the engine crankcase. When the vehicle is stored outside the garage during the cold season, after completing work on the line, drain the water from the cooling system.
5. In the warm season, fill the windshield washer reservoir with water.
6. If the vehicle has been operated in particularly dusty conditions or crossed fords and road sections filled with liquid mud, replace or clean the engine air filter element.
7. Wash the vehicle after driving if it has been driven on dirty or dusty roads.

1. Carry out the work provided for by the EO.
2. Check and, if necessary, adjust the free play of the clutch pedal.
3. Check the free play of the steering wheel, the clearances in the steering rod joints, in the pivot joints; check the splint of the nuts of the ball pins, the fastening of the steering knuckle lever, the ball pins, the ball bearings to the casings of the axle shafts, the steering bipod, the tightening of the nuts for fastening the tips and eliminate the detected malfunctions.
4. Check the amount of free and working travel of the brake pedal; if necessary, adjust the brake and its drive.
5. Check the fastening of the exhaust pipe of the muffler and its suspension.
6. Check wheel fastening, condition of tires and air pressure in them, pump air if necessary.
7. Check the fastening of the control drives of the gearbox, transfer case and, if necessary, tighten the threaded connections.
8. Check the fastening of the flanges of the front and rear cardan shafts to the flanges of the transfer box shafts and, if necessary, tighten the fastening.
9. Clear battery from dirt; clean the ventilation holes in the traffic jams; check the electrolyte level and top up with distilled water if necessary.
10. Check fan belt tension and alternator mounting.
11. Follow all the instructions in the lubrication table provided for TO-1.

1. Perform the work provided for TO-1.
2. Check clutch operation and clutch pedal free play. Adjust the clutch control actuator if necessary.
3. Check and, if necessary, adjust the gaps between the rocker arms and valves.
4. Check the mounting of the engine, engine oil sump, upper and lower parts of the clutch housing.
5. Check the fastening of the radiator and its lining, blinds, expansion rods.
6. Visually check the tightness of the cooling system, the serviceability and fastening of the cooling system pump and fan, the condition of the fan belt.
7. Clean the generator and starter from dirt and oil and check the condition of the collector and starter brushes. If necessary, blow out the cavity of the generator and starter with compressed air and check their fastening. Adjust fan belt tension.
8. Check the fastening of the intake and exhaust pipes.
9. Clean the surface of the spark plugs, the ignition coil of the distribution sensor and the high voltage wires from dirt and oil. Check the condition of the high and low voltage wires. Remove the spark plugs and check their condition. If necessary, clean the electrodes and adjust the gap between them.
10. Check the degree of charge of the battery by the voltage of the cells under load. If necessary, remove the battery for recharging. Check the fastening of the battery in the socket.
11. Check the fastening of the carburetor and fuel pump, troubleshoot. Adjust the idle speed of the crankshaft.
12. Check the mounting of the crankcase and bipod of the steering mechanism.
13. Check and, if necessary, adjust the engagement of the worm and steering roller.
14. Check front wheel toe-in, adjust if necessary.
15. Check the operation of the drive and the operation of the parking brake. If necessary, remove the drum, check the wear of the brake linings, disassemble, wash and lubricate the expansion and adjustment mechanisms.
16. Visually check the condition of the frame, springs, spring pads, cups, clamps and shock absorbers. Troubleshoot if necessary. Loose rivets of cups and clamps of springs should be re-riveted.
17. Check and, if necessary, adjust the wheel bearings.
18. Remove brake drums and clean brakes. Check the condition of the brake drums, shoes, linings and fastening of the brake shields.
19. Check the condition of the pipelines of the brake system and brake cylinders.
20. Install the brake drums and adjust the clearances between the brake drums and shoes.
21. Check the fastening of the leading flanges of the hubs and flanges of the axle shafts.
22. Check the fastening of the bearing caps of the drive gears of the front and rear axles.
23. Check the mounting of the gearbox on the clutch housing and transfer case on the gearbox.
24. Check the clearances in the bearings of the final drive gear of the front and rear axles and, if necessary, eliminate them.
25. Check fastening of cardan shaft flanges.
26. Check the fastening of the body (cabin) and platform to the frame.
27. Check and, if necessary, adjust the tension of the front door window cables.
28. Check the fastening of the fuel tanks.
29. Balance the wheels if necessary.
30. Clean the hoses through each TO-2 and rinse the parts of the closed crankcase ventilation system with kerosene.
31. Clean the air filter and its filter element from dust and dirt. Rinse the flame arrestor mesh inside the filter cover with kerosene. Replace the filter element with a new one every TO-2.
32. Follow all instructions in the lubrication table.

Seasonal maintenance is carried out twice a year - in spring and autumn, and, if possible, is combined with the next TO-2. When switching to the winter or summer season of operation, the scope of work on TO-2 should be supplemented with the following operations:
Before the summer season

1. Set the damper for heating the working mixture of the gas pipeline to the "summer" position.
2. Drain sediment from fuel tanks.
3. Remove the heater and wiper motors, check the condition of the collector and brushes, rinse and lubricate the bearings.
4. Flush the cooling system.
5. Change the oils in the units to the summer grades provided for in the lubrication table.

Before the winter season

1. Set the damper for heating the working mixture of the gas pipeline to the "winter" position.
2. Flush fuel tanks and fuel filters.
3. Replace the oils in the units with winter grades provided for in the lubrication table.
4. Prepare the starting engine heater for operation (when installing it).
5. Check the operation of the heating and ventilation system of the body (cabin).
6. Check the operation of the blinds. Troubleshoot and lubricate traction.
7. Clean or replace the brake booster air filter.

The section includes only a list of works. Information about techniques, methods of caring for systems, assemblies and components of the car and the necessary adjustments is set out in the relevant sections of the Guide.

Daily Maintenance

1. Visually check the completeness of the car, the condition of the body, windows, rear-view mirrors, plumage, license plates, paintwork, door locks, frames, springs, shock absorbers, wheels and tires. Eliminate detected faults.

Inspect the parking area and make sure that there are no leaks of fuel, oil, coolant and brake fluids. Eliminate detected faults.

Check and top up the level of coolant, crankcase oil and brake fluid.

2. Check the operation of the steering, brake systems, lighting devices, light and sound alarms, wiper. Eliminate detected faults.

3. Fill the windshield washer reservoir. In the warm season, the use of water is allowed.

4. If the car was operated in dusty conditions or crossed fords and sections of unpaved roads filled with liquid dirt, replace or clean the filter element of the engine air filter.

5. After the trip, wash the car if it was used on dirty or dusty roads.

Maintenance after break-in

1. Tighten the nuts of the engine cylinder head (except UAZ-31604).

2. Change the oil in the crankcases of the gearbox, transfer case, front and rear axles, flushing the units with spindle or industrial oil with a kinematic viscosity at a temperature of 50 °C not more than 14. The volume of flushing oil to be filled must be at least 75% of the filling rate.

3. Check the oil level in the crankcase of the steering mechanism or in the tank of the hydraulic booster system and top up if necessary.

4. Perform the work specified in the subsection "Car maintenance every 10,000 km", except for points 1, 7, 14, 15, 18.

5. Perform the work provided for in paragraphs 2, 5 of the subsection "Car maintenance every 20,000 km" .

Car maintenance every 500 km

1. Check and bring the tire pressure to normal.

2. Check and, if necessary, adjust the tension of the belts of the generator, the power steering pump.

3. On a new car, after the first 500 km run, tighten the steering gear housing mounts.

Car maintenance every 10,000 km

1. Check status brake pads and front brake disc. Replace if worn.

2. Check and, if necessary, adjust the free travel of the brake pedal.

Check the reliability of fastening of the mechanism and the parking brake actuator, tighten if necessary. Check the effectiveness of the parking brake. Adjust if necessary.

Check tightness hydraulic drive, the condition of the pipelines and hoses of the brake system. Eliminate faults.

Check the efficiency of the front and rear circuits of the brake system, the operation of the brake force pressure regulator.

3. Check the free play of the steering wheel, the condition, tightness and cotter pin nuts of the ball pins of the steering rods, the clearances in the hinges of the steering rods and the steering mechanism, the fastening of the steering knuckle lever, bipod and steering gear housing. Eliminate faults, tighten fastenings, if necessary, adjust the steering mechanism.

4. Check the condition of the front and rear suspension elements. Eliminate faults, replace worn hinges and deformed rods, tighten fasteners.

5. Check and, if necessary, adjust the wheel bearings.

6. Check the condition of the tires. If detected uneven wear front tires, check and adjust the toe-in of the front wheels.

8. Tighten the fastenings of the flanges of the front and rear propeller shafts to the flanges of the shafts of the transfer case and axles, ball bearings to the flanges of the axle shaft housings, and the leading flanges to the hubs.

9. Tighten the engine mounting, engine oil sump, upper and lower parts of the clutch housing, fuel lines, intake and exhaust manifolds, muffler downpipe and its suspension. On a UAZ-31604 car, in addition, tighten the fastening of the high-pressure fuel pump, connecting elements of glow plugs, air hoses, turbocharger, and connection of the turbocharger to the exhaust manifold.

10. Tighten the fastening of the radiator and its lining.

11. Check the condition of the alternator belts, power steering pump, vacuum pump. Replace worn belts. Adjust belt tension.

12. Check and, if necessary, adjust the gaps between the rocker arms and valves (UAZ-3160,

31601, -31605).

13. Check the tightness of the power system. Troubleshoot.

14. Rinse strainer fuel pump (UAZ-31601).

15. Replace filter element fine cleaning fuel.

16. Clean the air filter and its filter element from dust and dirt. Rinse the flame arrestor screen inside the air filter cover.

17. Clean the battery from dirt, clean the ventilation holes in the plugs, check the electrolyte level and, if necessary, top up with distilled water and charge the battery.

18. Clean the generator and starter from dirt and oil, check the condition of the collector and brushes. If necessary, replace the brushes, blow out the cavity of the generator and starter with compressed air and check their fastening.

19. Remove dirt and oil from the surface of the spark plugs, ignition coil, distribution sensor and high voltage wires. Check the distribution sensor, the condition of the high and low voltage wires. Remove spark plugs and check their condition. If necessary, clean the electrodes and adjust the gap between them. Check installation security high voltage wires in the sockets of the cover of the sensor-distributor and the ignition coil. Check the ignition timing setting (UAZ-31601).

20. Check fuel level in float chamber carburetor, work accelerator pump and economizer (UAZ-31601). Eliminate malfunctions.

21. Adjust the idle speed of the crankshaft (except for UAZ-3160, -31605) and check the toxicity of exhaust gases (except for UAZ-31604). Adjust the air-fuel mixture if necessary.

Car maintenance every 20,000 km

1. Check the condition of the brake pads rear wheels and parking brake system. Replace extremely worn pads.

2. Adjust headlights.

3. Check the clearances in the bearings of the gears of the main gear of the front and rear axles and, if present, eliminate them.

4. Check and, if necessary, adjust the tightness of the steering knuckle pins.

5. Check and, if necessary, tighten the fastenings of all units, assemblies, transmission parts, engine and body to the frame.

6. Drain sediment and flush fuel tanks.

7. Clean the hoses and wash the parts of the crankcase ventilation system with kerosene.

8. Check the thermostat, temperature sensors, fan clutch for proper operation. Check the condition of the hoses and connections. Troubleshoot. Faulty thermostat and sensors, replace damaged hoses.

9. On the UAZ-31604 car, check the operation of the glow plugs.

Car maintenance every 30,000 km

1. Change the oil in the engine crankcase, after flushing the lubrication system.

2. Remove starter from vehicle and service.

Car maintenance every 40,000 km

1. Replace the alternator belt (UAZ-31604).

2. On the UAZ-31604 car, check the spraying of the nozzles.

Car maintenance every 60,000 km

The odometer showed 15,000 kilometers. This means that it is time to do the scheduled TO-1. In addition to it, you need to change the oil in the front axle, because ...

Since in a more detailed study of work orders from Soffit, I suddenly realized that on the TO-0 I made, the oil was replaced only in the rear axle. It was already six months ago, so it’s hard to say what exactly happened: either I said something wrong, or we didn’t understand each other with the receiving master.

Thus, you first need to purchase engine oil and front axle.

Since the last oil change, I still have about 3 liters of engine oil left, so I bought one 4-liter Lukoil canister for the engine:

and two Lukoil canisters with a volume of one liter for the bridge:

In the last post about changing the oil, I explained why I choose Lukoil as a supplier of lubricants.

Like last time, I buy oil at a Lukoil gas station, where, as I also mentioned earlier, the chance to stumble upon a fake is minimal.

I made an appointment at the service station for the next day.

During a scheduled inspection, the master revealed some wear and tear drive belt generator. We have heard a lot about this feature of factory parts, so I agreed with the recommendation of the master to replace the belt. A low coolant level was also noticed. This misunderstanding has also been corrected.

All work took about 4 hours, except for washing the car, therefore, my recommendation: you should take care of your leisure in advance for the duration of the maintenance work.

V total, according to the works and materials of the service station, cost of TO-1 amounted to 7343 rubles. If we take into account the oil I bought, then this is another two thousand rubles. So in the end: ~ 9400 rubles.

But, depending on the operating conditions of the UAZ, maintenance intervals change. If the car is operated in harsh conditions or an extreme type of driving is used, then the frequency of maintenance is shifted towards reducing its intervals from 10,000 km to 5,000 km.

TO - 0 (2000km)
	300
	300
Engine - oil change and oil filter with flushing	750
	0
	1050
Transfer case - oil change	450
Gearbox - oil change	450
	300
Power steering oil - level check	150
	300
	600
	750
	750
	750
	750
Broach of the cooling system, fuel lines and nozzles, exhaust gas systems and manifolds	1050
	300
	0
	1500
Pivots - lubrication (set)	600
Front axle gearbox - oil change	300
Reducer rear axle- Change of oil	300
Tie Rod Joints - Grease	450
Crankshaft and alternator pulley - broach fasteners	300
	150
Total:	12600 Sign up
TO - 1 (10.000 km)
Rear cardan shaft - lubrication	300
Front cardan shaft - lubrication	300
	600
Diagnostics of the chassis, the state of the elements of the front and rear suspension and steering	0
Left hub bearings - adjustment	750
Right wheel bearings - adjustment	750
Broach fastening cardan shafts, leading flanges to the hubs, steering	750
Attachment drive belt - adjustment (for 1 pc.)	300
	600
	150
Technical fluids - checking levels	0
Pivots (set) - lubrication	600
Wheel alignment angles - adjustment	1500
Tie Rod Joints - Grease	450
Total:	7050 Sign up
TO - 2 (20.000 km)
Rear cardan shaft - lubrication	300
Front cardan shaft - lubrication	300
Engine - oil and oil filter change	600
Diagnostics of the chassis, the condition of the elements of the front and rear suspension and steering	0
	150
	450
Power steering oil - level check	150
Engine mounts - broach mounts	300
Suspension front and rear - broach fasteners elements	600
Broaching of fasteners of units, units and parts of transmission, engine and body to the frame	750
	450
Technical fluids - checking levels	0
Fuel filter - replacement	600
Air filter - replacement	900
Pivots (set) - lubrication	600
Tie Rod Joints - Grease	450
Coolant pump pulley - broach	150
Total:	6750 Sign up
TO - 3 (30.000 km)
Rear cardan shaft - lubrication	300
Front cardan shaft - lubrication	300
	750
ECM and ABS computer diagnostics	1050
Diagnostics of the chassis, the condition of the elements of the front and rear suspension and steering	0
Broach fastening cardan shafts, leading flanges to the hubs, steering	750
Attachment drive belt - adjustment (for 1 pc.)	300
Headlights - direction adjustment	600
Parking brake - adjustment	150
Left hub bearings - adjustment	750
Right wheel bearings - adjustment	750
Pivots (set) - lubrication	600
Technical fluids - checking levels	0
Wheel alignment angles - adjustment	1500
	450
Total:	8250 Sign up
TO - 4 (40.000 km)
Rear cardan shaft - lubrication	300
Front cardan shaft - lubrication	300
Engine - oil and oil filter change	600
Diagnostics of the chassis, the condition of the elements of the front and rear suspension and steering	0
Control hole in the pump of the cooling system - cleaning	150
Power steering oil - level check	150
Engine mounts - broach mounts	300
Suspension front and rear - broach fasteners elements	600
	0
Broaching of fasteners of units, units and parts of transmission, engine and body to the frame	750
Spark plugs - replacement	1050
Technical fluids - checking levels	0
Oil in units - replacement	1500
Hinges and door locks - lubrication	450
Air filter - replacement	900
Pivots (set) - lubrication	600
Tie Rod Joints - Grease	450
Total:	8100 Sign up
TO - 5 (50.000 km)
Diagnostics of the chassis, the condition of the elements of the front and rear suspension and steering	0
Wheel alignment angle - adjustment	1500
ECM and ABS computer diagnostics	1050
Technical fluids - checking levels	0
Attachment drive belt - adjustment	300
Power steering oil - replacement	600
Alternator and starter mounts - broach	300
Broach fastening cardan shafts, leading flanges to the hubs, steering	750
Headlights - adjustment	600
Engine - oil and oil filter change	600
Rear cardan shaft - lubrication	300
Front cardan shaft - lubrication	300
Tie rod joints (set) - lubrication	450
Pivots (set) - lubrication	600
	600
	750
Lubrication of front and rear wheel hub bearings - replacement	6000
Fuel filter - replacement	600
Injector - flushing	2300
Total:	17600 Sign up
TO - 6 (60.000 km)
Rear cardan shaft - lubrication	300
Front cardan shaft - lubrication	300
Engine - oil change and oil filter with flushing	750
Diagnostics of the chassis, the condition of the elements of the front and rear suspension and steering	0
Engine mounts - broach mounts	300
Hinges and door locks - lubrication	450
ICE suspension - condition check	0
Left hub bearings - adjustment	750
Right wheel bearings - adjustment	750
Broaching of fasteners of units, units and parts of transmission, engine and body to the frame	750
Alternator belt with rollers - replacement	1500
Parking brake - adjustment	150
Technical fluids - checking levels	0
Coolant pump pulley - broach	150
Air filter - replacement	900
Coolant - replacement	1200
Pivots (set) - lubrication	600
	450
Tie Rod Joints - Grease	450
Total:	9750 Sign up
TO-7 (70,000 km)
Diagnostics of the chassis, the condition of the elements of the front and rear suspension and steering	0
Wheel alignment angles - adjustment	1500
ECM and ABS computer diagnostics	1050
Technical fluids - checking levels	0
Attachment drive belt - adjustment (1 pc.)	300
power steering oil - level check	150
Suspension front and rear - broach fasteners elements	600
Alternator and starter mounts - broach	300
Broach of the cooling system, fuel lines and nozzles, exhaust gas systems and manifolds	1050
Broach fastening cardan shafts, leading flanges to the hubs, steering	750
Engine - oil and oil filter change	600
Rear cardan shaft - lubrication	300
Front cardan shaft - lubrication	300
Tie rod joints (set) - lubrication	450
Oil in units - replacement	1500
Pivots (set) - lubrication	600
Total:	9450 Sign up
TO - 8 (80,000 km)
Diagnostics of the chassis, the condition of the elements of the front and rear suspension and steering	0
ICE suspension - condition check	0
Left hub bearings - adjustment	750
Right wheel bearings - adjustment	750
Technical fluids - checking levels	0
Parking brake - adjustment	150
Broaching of fasteners of units, units and parts of transmission, engine and body to the frame	750
Engine mounts - broach mounts	300
Coolant pump pulley - broach	150
Fuel filter - replacement	600
Control hole in the pump of the cooling system - cleaning	150
Spark plugs - replacement	1050
Engine - oil and oil filter change	600
Rear cardan shaft - lubrication	300
Front cardan shaft - lubrication	300
Tie rod joints (set) - lubrication	450
Hinges and door locks - lubrication	450
Pivots (set) - lubrication	600
Air filter - replacement	900
Fuel pump filter - replacement	1500
Total:	9750 Sign up
TO - 9 (90,000 km)
Diagnostics of the chassis, the condition of the elements of the front and rear suspension and steering	0
ECM and ABS computer diagnostics	1050
Wheel alignment angles - adjustment	1500
Technical fluids - checking levels	0
Attachment Drive Belt - Inspection	300
Power steering oil - level check	150
Alternator and starter mounts - broach	300
Broach fastening cardan shafts, leading flanges to the hubs, steering	750
Headlights - direction adjustment	600
Engine - changing oil and oil filter with pumping	750
Lubricating the bearings of the hubs of the front and rear wheels - replacement with broaching of the brake	6000
Rear cardan shaft - lubrication	300
Front cardan shaft - lubrication	300
Tie rod joints (set) - lubrication	450
Steering column shaft bearings - lubrication	450
Pivots (set) - lubrication	600
Timing chain - replacement	18600
Total:	32100 Sign up
TO -10 (100,000 km)
Diagnostics of the chassis, the condition of the elements of the front and rear suspension and steering	0
ICE suspension - condition check	0
Technical fluids - checking levels	0
Left hub bearings - adjustment	750
Right wheel bearings - adjustment	750
Oil in units - level check	450
Parking brake - adjustment	150
Broaching of fasteners of units, units and parts of transmission, engine and body to the frame	750
Broach fastening cardan shafts, leading flanges to the hubs, steering	750
Engine - oil and oil filter change	600
Rear cardan shaft - lubrication	300
Front cardan shaft - lubrication	300
Tie rod joints (set) - lubrication	450
Engine mounts - broach mounts	300
Suspension front and rear - broach fasteners elements	600
Coolant pump pulley - broach	150
Fuel filter - replacement	600
Control hole in the pump of the cooling system - cleaning	150
Hinges and door locks - lubrication	450
Injector - flushing	2300
Clutch fluid - replacement (with pumping)	600
Brake fluid - replacement (with pumping)	750
Total:	11150 Sign up

Seasonal maintenance of UAZ cars

The operation of a UAZ car is also characterized by such a type of service as seasonal! The work required for seasonal maintenance is indicated in the operating instructions for the UAZ vehicle. Seasonal maintenance is carried out 2 times a year - in spring and autumn, and may or may not coincide with the next MOT.

Maintenance of a UAZ car before the summer season of operation

1. Check the condition of the oil pump drive gears by first removing its cover.
2. Drain sediment from fuel tanks.
3. Check the operation of the wiper and washer. Troubleshoot
4. Replace the oils in the units with summer (all-weather) grades, prudently using the lubrication table
5. Flush the cooling system
6. Set the damper for heating the working mixture of the gas pipeline to the “summer” position

Maintenance of a UAZ car before the winter season of operation

1. Check the density of the liquid in the engine cooling system and, if necessary, bring it to normal (1.075-1.085 g / cm3 at 20 degrees C)
2. When filling the washer tank with anti-freeze liquid, drain the water
3. Check the operation of the heating and ventilation system of the body. Troubleshoot.
4. Before the winter season of operation (or after 20,000 km of run), flush the fuel tanks
5. Replace the chassis in the units with winter grades specified in the lubrication table.
6. Set the damper for heating the working mixture of the gas pipeline to the “winter” position
7. Check the operation of the blinds. Troubleshoot, lubricate traction.
8. Close the oil cooler tap.