Owners Hyundai Creta began to complain about the quality of the metal and paintwork. Most often, on machines no older than 4 months, the fifth door begins to rust.

Dealers traditionally do their best to avoid warranty repair, but this does not happen often.

According to the Wordstat service: the problem appeared in December 2016 and the number of requests to Yandex is growing steadily.

Here is a selection of messages from Creta owners who have noticed this problem:

Guys, a problem arose, two dots formed on the fifth door, at first I thought the dirt tried to wipe them off and nothing, as a result, rust. I'll take a photo and post it, wow, the car is 4 months old.

I don't believe this could happen...

I'll wait for spring, and then we'll see. If nothing else pops up with a sticker, I'll close it. Production September 2016, acquired September 23, 2016.

I have the same. Two red spots appeared on the trunk lid (next to the brake light) for 4 months. Everything was done under warranty with no issues. At first I was upset, like a new car … apparently I'm not the only one.

It is expected that the main concentration of owners of Crete affected by rust on the forum of the same name. Members have already created a petition. Not many subscribers yet. It is still too early to talk about a mass problem, but the trend is noticeable.

According to many photos posted on the forum, not the highest quality work of Hyundai masters with metal body parts is noticeable.

Those who noticed pockets of corrosion on the trunk lid appeared in early 2017. Basically, distinct traces of swelling of the paintwork flaunted on the outer panel of the body element. And often the trouble overtook fresh cars that were operated for only three to four months. In the initial period, it seemed that the problem affected only the owners of cars of certain colors (white and silver), but the rest of the palette was quickly “noted” as well.

Most of the employees dealer centers behaved correctly and after inspecting the cars, they decided to repaint the suspicious part. Although there were enough cases when negligent warranty engineers managed to find mythical traces of external mechanical impact (micro-chips) and turned the owners around. According to representatives of one of the dealer services, already in February 2017, technical centers began to send information on this problem to the manufacturer. The plant instructed to repaint or change covers depending on the specific case, and also send parts to him for examination.

Alas, ordinary owners were in an informational vacuum, and the manufacturer did not indulge in comments, limiting himself to saying that the percentage of problem cars was negligible compared to the volume of all cars sold up to that moment. As a result, passions and disputes flared up on the forums in an attempt to independently understand the issue and understand the real extent of the trouble. According to the results of questionnaires on websites, about 25% of owners encountered. A logical continuation of the story was a collective electronic petition addressed to the manufacturer. True, she did not collect as many signatures as expected.

Hyundai, including paintwork(5 years or 150,000 km) and, basically, the friendly policy of dealers in this matter. However, owners were very concerned about the nature of the rust problem. If the trunk lid gave up so quickly, then what can happen in a year or two with the rest of the body?! In addition, messages and photos of corrosion centers on the inner edges of the body element began to appear on the forums. Swelling of the paintwork appeared in the areas of rolling of the cover panels and on the edges of the niches under the lanterns. The reviews of some owners did not add optimism, talking about the reappearance of rust after repainting the cover and even after replacing it.

The result of an internal study of the issue was the release in May of this year of a technical bulletin prepared by the manufacturer. The document prescribes a mandatory inspection of cars manufactured between July 26 and December 15, 2016, which come to the service for any work. If corrosion is found in the places described above, the dealer must repair (repaint) or replace the cover. The issue is resolved in each case after cleaning the rust. If its traces cannot be completely removed, then it is necessary to replace the body element. Unfortunately, the bulletin does not contain information about the causes of the defect and changes in production.

ON THE COFFEE GROUNDS

Alas, the manufacturer did not give any comments on the request of the editors of "Behind the wheel" about the details of the rust problem. Therefore, it remains only to make assumptions, comparing the information received from some dealers and on the owners' forums, as well as the experience of operating Crete in our fleet.

Judging by the fact that the service bulletin applies to machines manufactured before December 15, 2016, there is hope that the causes of the defect have been found and changes have been made to the technological chain on the conveyor. At least, there is no information about similar problems on cars of 2017 release yet. The manufacturer did not want to reveal the secret, and the dealership employees are armed only with assumptions about the causes of such a strange problem.

The actual scale is also unclear. Questionnaires at two major forums showed that about 25% of owners encountered rust. However, only 850 people took part in these votings. The collective electronic petition has not collected so much either - today it has only 427 signatures. For understanding, almost 22,000 Crete were sold in 2016. Some dealers also talk about the low percentage of "sick" cars identified during the period of validity of the service bulletin. That is, on paper, owners of cars manufactured before December 15, 2016 do not have many chances to see rust on the trunk lid, but no one is immune from this.

In the process of disputes about the nature of rust, a curious fact surfaced - uneven and in some places too small layer thickness. There are videos on the Internet where the instruments show only 80 microns on the edges of the body panels, as if there is no varnish. At the same time, the video participants confirm on calibrated probes that the thickness gauge is calibrated correctly.

Paint thickness has been tested on several machines. It was not possible to see examples with indecently low 80 microns, but there were some thin and too heterogeneous places. The experiment involved two Cretas from our fleet (2016) and several new cars (2017), which were still waiting for buyers. In general, all participants with different body colors showed similar results.

Indeed, the coating layer on the edges of the body panels is thin (100–110 microns), but these are not criminal values. For the most part, the difference in thickness across the entire vehicle ranges from 120 to 150 microns, which is normal for new car in factory paint. However, there are examples of a very significant discrepancy on one body element. The brightest of them is the ribs of the front doors. Under the mirrors, the calibrated instrument shows about 160 microns, and above the handle - 120 microns. Strange numbers, given that it is robotized in all modern factories. Alas, these facts were left without comment from the manufacturer.

Many auto giants distinguished themselves with “rusty” problems at one time. Some of them were famous weak spots on the trunk lid - niches under the plastic lining. After a couple of years of operation, rust appeared in these places. This hurt the second generation and the first Mazda CX-9. Toyota stood out more brightly with rusting hoods on fresh cars. In the first case, when the owner complains to warranty period and the absence of traces of external influence, the part was repainted, and in the second, the manufacturer, known for its policy on recall campaigns, organized a whole service campaign to correct the defect on the cars sold.

Given the many years of experience of similar ones, it is unlikely that problems with the trunk lid on Krets speak of misses throughout the body. However, the Koreans could have shown more attention to the concerns of the owners and lifted the veil of secrecy. Sooner or later, all auto giants make mistakes, especially for cars of the first years of production. No one raises suspicions and questions when the manufacturer admits some mistakes and announces adjustments to the production cycle, not forgetting about warranty obligations to the owners of potentially “sick” machines. But the information vacuum only cultivates fears and generates negativity.

Photo: Stas Panin and club-creta.ru

Why do the new Hyundai Creta rust - investigation "Behind the wheel" Why rust new Hyundai Creta - investigation "Behind the wheel"

No one doubted that the Hyundai Creta body would be galvanized. However, the news about the purchases of Russian metal alarmed some. However, in vain.

After the announcement of the imminent start of sales of the new Korean SUV, many motorists became interested in the question - is the body of the Hyundai Kreta galvanized? Of course, few dare to think that automobile concern with a worldwide reputation will sell cars that will rust in a year or two. However, after the news that Russian metal will be used for production, potential buyers have a question about its quality. Will it compare with Korean steel? And which anti-corrosion treatment will the Creta bodywork be subjected?

Korean technology

During the production of the SUV, several types of metal are used:

- galvanized steel type Hyundai Hysco;

— stainless steel of BNG Steel and POSCO types.

Steel from Posco is also used for the production of SUV components.

This steel is highly resistant to corrosion and withstands the effects of aggressive environments. In addition, SUV bodies are additionally processed at factories. This happens by cataphoretic priming, for which a primer is used, developed with the use of epoxyamine-type components, characterized by a reduced drying temperature, as well as copolymers (vinyl and acrylic), which contain resins of amine groups.

For the body of the crossover, galvanized steel is used.

The strength of Hyundai cataphoretic priming is that, with a thin protective layer, an excellent degree of metal protection is achieved. In combination with galvanization, the car body successfully resists not only corrosion, but also alkalis, salts and other reagents. The use of such methods allows the concern to guarantee the quality of its products.

Use of Russian metal

If confidence in Korean technologies in Russia is growing from year to year, then many are wary of the news that the metal for the Hyundai Kreta model will be supplied by the domestic concern Severstal. It is with this conglomerate that Hyundai Motor Manufacturing Rus signed a contract until the end of 2016, which implies the shipment of cold-rolled and galvanized metal products. The Cherepovets Metallurgical Plant will supply steel for the assembly plant. In reports from the metallurgical giant and Hyundai, it has been said more than once that the products purchased from Severstal fully comply with all the standards of the Korean manufacturer.

Severstal was chosen as the Russian metal supplier.

In this case, both parties can consider the signed contract successful. After all, Severstal has received a new, solvent client, which is especially important in the light of anti-dumping investigations initiated in the EU against Russia and China. As a result of the case, duties were introduced on Russian cold-rolled steel. Hyundai gets an excellent opportunity to reduce the cost of the SUV and increase the degree of localization.

Plant Hyundai Manufacturing Rus.

At the moment, localization is about 50%. However, its main factor is local workers. At first glance, a wide range of products is supplied to the plant Russian production. However, for the most part, these are either repackaged or foreign components assembled in the Russian Federation.

Russian steel

The metal supplied by Severstal is galvanized cold-rolled sheets. This coating guarantees effective protection against corrosion. The amount of zinc used depends on the preferences of the customer and can reach up to 450 g/m². Regarding the thickness of galvanizing, there is no data on it, however, it is known that the thickness of Hyundai Creta body panels ranges from 0.6 to 0.8 mm. Therefore, it is clearly not worth fearing the appearance of rust on the body of the crossover.

Anodizing body Hyundai Creta

Galvanizing body components Hyundai Creta, like other cars, occurs by applying protective coating anode method. It lies in the fact that automotive steel is coated with a layer of metal with a lower electrochemical potential - zinc.

An example of galvanized metal plating.

The peculiarity of this method is that it not only causes mechanical insulation of steel, but also guarantees electrochemical protection. This means that even minor damage to the zinc layer, which is inevitable during the operation of Creta (chips and scratches from pebbles, branches, etc.), will not lead to corrosion. In contrast to the cathodic coating, which can only provide protection if the layer is intact.

Creta body galvanizing technology

Galvanizing of a body of this crossover is carried out by a galvanic method. Of course, it is inferior in efficiency to thermal galvanizing, which is used for premium model bodies, but it is significantly better than cold galvanizing. In general, this method is optimal for the SUV in terms of price / efficiency.

Galvanic galvanization of the Hyundai Creta occurs according to the following scheme:

1. The Creta body is immersed in a special container filled with a zinc solution.
2. Next, the terminal (negative) is connected from the source of electric current to the body.
3. The capacity is powered from the positive terminal.

The body is immersed in a bath of zinc solution.

Due to the electric current in the tank, electrolysis occurs, which creates a layer of zinc on the surface of the body. This layer reliably protects the car body, and its lower price (compared to the thermal method) allows you to keep an adequate price.

Many fans of the Korean lineup are interested in the design Hyundai body Creta. Note that the development of the trolley was carried out by specialists from several technology centers. What happened in the end? This is exactly what we will talk about in today's article.

The body is one of the most important parts of a car. But, oddly enough, Special attention framework design began to be given relatively recently. If earlier, the cart was no more than just a piece of metal, now it is an aerodynamic element made of quality materials.

Development process

As you know, the Hyundai company is not only an automotive concern, but also a huge conglomerate that includes a large number of enterprises, including metallurgical ones. This is very convenient, since in the manufacture of the Hyundai Creta body, manufacturers have the opportunity to use steel of their own production.

The process of developing the frame of the Korean crossover took almost three years, because the first notifications about the start of work appeared back in 2011. Above, we have already said that the body of the Hyundai Crete was designed by specialists from several technology centers, which closely interacted with each other.

Initially, the Hyundai Creta body structure was designed using computer programs, after which the developers made several test samples that passed a series of tests. In the end, one option was chosen, which later formed the basis of the Hyundai Creta bogie. It is worth noting that the frame of the “Korean” has proven itself well in crash tests conducted by Chinese and Latin American specialists.

Body Features

The Hyundai Creta frame is assembled by welding, which is automated and performed by special robots, which completely eliminates the human factor. It is worth noting that before getting on the welding conveyor, the frame elements of Creta pass through the stamping shop, where they are pressed. In the end, a finished frame comes off the welding line, in which there are no doors and a hood.

The Hyundai Creta body structure uses several types of steel at once:

• Anti-corrosion steel.
• High strength steel.
• High-tech metal used in the front of the car.

The use of these materials allowed manufacturers to increase the resistance of the crossover in frontal impact. In addition, the use of several types of steel helped to reduce the curb weight of the car.

It should be noted that in the region engine compartment installed a special transverse amplifier. In addition, the side racks are additionally reinforced.

As for the roof, it is equipped with 5 supports at once, which are able to prevent severe crushing in the event of a car overturning.

However, all the listed features of the Hyundai Kreta cart are only a small part of what Korean developers have pleased us with.

Hyundai Creta- Solaris among crossovers. It is inexpensive when compared with competitors, the cost of the minimum configuration on the market is 800 thousand rubles, the “maximum speed” will cost 1.2 million rubles. The crossover is pleasant to look at, outwardly the model is practically no different from its fellow tribesmen, at least for the worse. Good quality finishing materials, comfort and ergonomics are provided. However, there are several significant “BUTs” that make the operation of the Korean crossover a real nightmare and a big disappointment for the newly minted Crete owners.

We have collected some of the most egregious facts that indicate that the crossover from Korea is far from the best. the best way for purchase.

1. Hyundai Creta body rots!

Photo taken from www.drive2.ru

The first and most terrifying fact about the Hyundai Creta is that its body rots just months after leaving the assembly line! What a news!

A considerable number of motorists who managed to take possession of the crossover spoke about this fact, and what they said was shocking, they simply could not believe it. Nevertheless, all the stories turned out to be true, a number of automotive publications that you can trust wrote about this, including information that was published on the magazine's website. "Behind the wheel".

According to data from the forums, from a quarter to a third of owners have encountered this unpleasant ailment. And it would be nice if the bottom of the car was covered with rust, at least you can “catch” it. But traces of metal decomposition appeared on the body panels and even on the roof!!! What is it like? You can read more about the study in the article "Why do the new Hyundai Creta rust - investigation "Behind the wheel""

And in order not to slander the Korean automaker, we note that according to official data, car owners who have encountered a rust problem on Hyundai Creta are very few, 1 percent will not be typed.

Therefore, you should not panic. However, it is best to keep in mind that there is a similar problem.

In order not to tarnish its reputation, Hyundai will change the necessary technical processes (or has already made changes) for any reason, and new batches will get rid of an unpleasant ailment. But the residue will remain...

2. Crossover with a 1.6 liter engine, automatic and all-wheel drive has slurred dynamics

The second unfortunate disappointment of the owners is that the Creta, equipped with a 1.6 liter engine, automatic transmission and all-wheel drive does not run at all. For example, the following review https://www.zr.ru/cars/hyundai/-/creta/reviews/

We immediately note that this is almost maximum equipment and it costs more than 1.1 million rubles.

According to the passport, acceleration is 13.1 seconds, not fast, but it would seem that you can live, because we don’t take a sports car. In life, everything turned out to be somewhat worse (according to the forum users), since acceleration from 0 to 100 km / h is not the only mode of movement in real road conditions, much more often you need to quickly accelerate from 3rd, 4th gear, and here everything turns out to be quite bad. A car with a 123 horsepower engine does not pull out, acceleration is sleepy and does not quite fit the realities of modern road life.

However, the disease is treated very simply, take a model with a 2.0 liter engine, overpay a little (60-100 thousand rubles), but immediately raise the safety of operation by a few points up.

P.S. People's opinions about the dynamics in the discussions differ. For some, power and high-torque is enough and they do not understand the essence of the claims of other owners. Forum club-creta.ru

3. Minimum equipment - no, no!

Hyundai differs from many in a fairly budget approach to pricing, but according to the old and unkind tradition, if you want to buy a car as cheaply as possible, do not do it, otherwise you will lose. For 800 thousand rubles in the Start package, you will get a kind of crossover with a mono-wheel drive on the front axle, two frontal airbags, 16” steel wheels and a set of “options” that even Lada Kalina has, like classic electric windows, central lock and immobilizer.

Tell me honestly, would you buy a completely "naked" car for 800 thousand? Well, this is a crossover, whatever one may say, and not a car of the brand. With all due respect to the effort domestic auto industry get out of the impenetrable dense darkness. In this, our fellows inspire optimism.

4. Creta is expensive

Yes, we say that the crossover is budget, read, inexpensive. But if we discard minimum configuration and choose a more or less worthy one, it turns out that it is better to purchase a model from only 1 million rubles. ONE MILLION Carl!

What is it like? It is not expensive?! Expensive of course.

We understand that the crossover has always been an expensive pleasure and the manufacturer cannot sell its products at a loss, but ... Creta is really an expensive model from Hyundai in the budget segment.

5. Buying queues

At the same time, to buy Creta will have to wait. The wait will be long. In some regions, the queue is scheduled for almost six months. This is both a merit and a mistake of the manufacturer. On the one hand, the excitement is crazy, people want to get their hands on Creta, on the other hand, it would not hurt to arrange deliveries or production in a larger volume. Discussion on the forum www.hyundai-creta2.ru

This was the top 5 most egregious Hyundai Creta facts. Of course, car owners will find a bunch more flaws or just taste flaws in the car and the forums are full of discussions of this kind. We will not list negative reviews, because in our opinion, this will already be nit-picking.

What do we want to say with this material? Does not exist perfect cars. They do not exist in nature, even ultra-reliable Toyotas break down. Remember after 7 years of operation. But in pursuit of imaginary savings, it’s better to slow down and think about whether it’s worth getting a loan or giving away money accumulated over the years to buy a crossover, but in fact an ordinary city car named Creta? Maybe it's better to take a brand new Solaris of the second generation, a bestseller of the Russian market, proven, honed over the years of release, and not to know the troubles? Or do you still think that it is worth overpaying for all-terrain qualities crossover Creta? You decide.