Electrical equipment of motorcycles IZH 7.107-01

The electrical diagram is given in Appendix 6. The electrical equipment of the motorcycle includes:

sources of electricity - a battery and a generator;

control device - rectifier-voltage regulator;

ignition devices - ignition coil, sensor, switch and spark plug;

lighting and signaling devices - a headlight, a rear lamp, direction indicator lamps, an audible signal (for a motorcycle with a side trailer, an additional front marker lamp and a rear lamp);

control and monitoring devices - ignition switch, control lamps, turn indicator interrupter, lighting mode switch, horn switch, turn indicator switch, lighting mode switch, alarm switch high beam, emergency switch engine, stoplight switch for front and rear wheel brakes.

5.4.1. Motorcycle generator IZH 7.107-01

The alternator (Fig. 30) is single-phase with excitation from permanent magnets.

The generator rotor is mounted on the cone of the right semi-axis crankshaft engine, the stator - in the cover of the generator or on a base fixed in the engine crankcase. The stator has two separate windings: charging and power. The charging winding is connected directly to the switch and serves to power the engine ignition system, the power winding through the rectifier-regulator provides power to lighting devices, alarms and battery charging.

Rice. 30. Generator and ignition sensor:

1 - rotor; 2 - stator; 3 - ignition sensor

The ignition system is powered by alternating current, the remaining consumers through a rectifier-voltage regulator with direct current.

The generator does not have sliding contacts and rubbing parts, its maintenance is reduced to monitoring the state of electrical insulation, wire connections and the reliability of the rotor and stator fastening.

The serviceability of the generator set (generator-rectifier - voltage regulator) is checked using a voltmeter direct current with a scale division value of 0.1 V. The voltmeter is connected to the "+" terminal of the rectifier-voltage regulator and "mass". At medium engine speeds with the battery connected and the high beam headlights on, the voltage should be 13.7 ... 14.7 V. A voltage deviation from the indicated values ​​\u200b\u200bindicates a malfunction of the rectifier-voltage regulator or generator.

Remove the generator from the engine in the following order:

disconnect the wires of the generator and the ignition sensor from the rectifier-voltage regulator, switch, main harness;

remove the generator cover with the stator, unscrew the four screws securing the stator and the screw of the bracket for attaching wires to the generator cover, disconnect the stator from the generator cover;

unscrew the rotor fastening bolt, using the screw from the chain link axle squeezing tool as a puller (screw it into the rotor shaft), remove the rotor.

If the stator is mounted on a base fixed in the crankcase, unscrew the four screws securing the stator to the base, remove the stator with the harness.

Install the generator in reverse order.

5.4.2. Motorcycle battery IZH 7.107-01

The battery is the source of power when the engine is not running. The "-" terminal of the battery is connected to the "mass" of the motorcycle. Reverse connection of the terminals is unacceptable, as it leads to failure of electronic devices, other components of electrical equipment and the battery itself.

The actuation, operation and maintenance of the battery are described in the attached battery instruction manual.

A capacitor with a capacity of 2200 microfarads is connected in parallel with the battery, designed to smooth out the rectified voltage ripples and ensure the normal operation of motorcycle electric power consumers in the event of a battery failure or its absence.

5.4.3. Rectifier-voltage regulator for motorcycles IZH 7.107-01

The rectifier-voltage regulator (Fig. 31) or voltage regulator is designed to rectify the alternating current of the generator, maintain the generator voltage within the specified limits and ensure reliable operation of the entire electrical equipment system, the connection of which to the system is different (see the electrical diagram in the appendix 7).

Rice. 31. Scheme of the rectifier-voltage regulator BPV 21-15

In order to avoid violation of the thermal mode of operation of the rectifier-regulator, periodically (at least once every six months) it is necessary to clean it with a brush from dust and other contaminants. It is not allowed to clean with metal objects and break the factory seal during the motorcycle warranty period.

5.4.4. Installation of motorcycle ignition IZH 7.107-01

The initial ignition advance angle is determined by the relative position of the ignition sensor and the generator rotor; it cannot be adjusted during operation. When the engine is running, the ignition system automatically changes the ignition timing depending on the crankshaft speed.

5.4.5. Switch electronic motorcycles IZH 7.107-01

The electronic switch is designed to store the energy generated by the generator and transfer it to the ignition coil.

The switch is made in a plastic hermetically sealed case, which prevents moisture from entering. Care does not require, repair is not subject.

5.4.6. Motorcycle ignition sensor IZH 7.107-01

The ignition sensor (Fig. 30) is designed to create a control pulse for the ignition switch. During operation, maintenance is not required and cannot be repaired.

5.4.7. Motorcycle ignition coil IZH 7.107-01

The ignition coil (Fig. 32) is designed to convert the energy stored in the switch into a high-voltage pulse applied to the spark plug. During operation, it is necessary to clean the coil from dust and other contaminants.

Not subject to repair.

Rice. 32. Ignition coil

5.4.8. Motorcycle spark plug IZH 7.107-01

After 2500-3500 km, check the condition of the candle, in case of carbon deposits and oiling, rinse the candle in clean gasoline and dry it.

Check the gap between the spark plug electrodes with a feeler gauge. When adjusting the gap, carefully bend the side electrode. Install the spark plug in the socket with the sealing ring.

5.4.9. The tip of the spark plug motorcycles IZH 7.107-01

The spark plug tip (Fig. 33) connects the spark plug to high voltage wire ignition coils and ensures the reduction of radio interference to acceptable standards. During operation, it is recommended to periodically check the reliability of fastening the wires in the tip and in the ignition coil, blow the tip to remove dust between the screen and the housing, wipe the tip inside. The wire must be screwed into the lug until it stops.

Rice. 33. Candle tip:

1 - body; 2 - resistor; 3 - wire; 4 - screen

5.4.10. Headlight of motorcycles IZH 7.107-01

The headlight has two lamps: the main light with two threads (dipped and high beam) and parking light. To better use the light qualities and reduce glare, the headlight must be adjusted. Before adjusting, place the motorcycle on a horizontal platform perpendicular to the Screen at a distance of 10 m. The load on the motorcycle during adjustment is the driver. Adjustment should be made with the low beam on in accordance with the markings of the screen (Fig. 34), while the longitudinal vertical plane of symmetry of the motorcycle should intersect with the screen along the line AB.

Rice. 34. Headlight adjustment

5.4.11. Brake light switches for motorcycles IZH 7.107-01

The brake light switches for the front and rear wheels are used to turn on the light signal when the motorcycle is braked. Adjustment of the moment when the signal is switched on in case of a change in the position of the rear wheel brake lever is carried out by moving switch 1 (Fig. 35) with its loosening. The brake light must come on before the wheel starts to brake.

The front wheel brake light switch is installed in the front wheel brake lever bracket and does not require adjustment.

Rice. 35. Stop light switch adjustment:

1 - stoplight switch; 2 - screw; 3 - nut; 4 - spring; 5 - thrust

5.4.12. Sound signal of motorcycles IZH 7.107-01

The sound signal does not require maintenance. The sound intensity can be adjusted with the adjusting screw located on the body.

5.4.13. Motorcycle fuse IZH 7.107-01

The fuse consists of a body 1 (Fig. 36), a cover 3 and a fusible insert 2 for 10 A.

The fuse is connected to the "+" terminal of the rectifier-voltage regulator.

If the fusible insert burns out, eliminate the cause that caused the combustion and replace it by disconnecting the body from the cover.

Monitor the condition of the contact connections of the fuse, cleaning them from contamination.

Rice. 36. Fuse:

1 - body; 2 - fusible insert; 3 - cover

5.4.14. Turn signal breaker

The breaker for direction indicators IZHRP-4 (Fig. 37) is designed to interrupt the power supply circuit of the signal lamps of the direction indicators and monitor the health of these lamps.

The direction indicator breaker is located on the frame under the gas tank. It has protection against short circuits in the circuit of signal lamps and does not require maintenance. Not subject to repair.

Rice. 37. Electrical circuit diagram of the turn signal breaker IZH RP.4:

"+" - positive conclusion; "-" - negative output ("mass"); H - load output

"Planet-sport" - the first Izhevsk motorcycle with 12-volt electrical equipment that meets all modern (as of 1982) requirements for this system.

(click on the picture to enlarge)

Scheme of the electrical equipment of the motorcycle IZH Planet Sport I - parking light lamp; 2 - main light lamp; 3 - neutral control lamp; 4 - resistor; 5 - oil pressure control lamp; 6 — the relay of indexes of turn; 7 - block of diodes (decoupling); 8 — a lamp of illumination of a scale of a speedometer; 9 - ignition switch; 10 — forward lanterns of indexes of turn; II - headlight switch and emergency ignition switch; 12 - brake light switch hand brake; 13 - relay-regulator; 14 - neutral lamp switch; 15 - high beam control lamp; 16 — a lamp of control of indexes of turn; 17 - lamp for monitoring the operation of the generator; 18 - sound signal; 19 - light switch and direction indicators, horn switch; 20 - spark plug; 21 - ignition coil; 22 - foot brake switch; 23 - generator; 24 - accumulator battery; 25 - fuse; 26 - rectifier; 27 - oil pressure sensor; 28 - taillights of direction indicators; 29 - rear light.

Improving the car, the plant made a number of changes to it. In particular, the fixation and clarity of operation of the switches IZH P101 and IZH P102 and the switch on the steering wheel have been improved. The optical element of the Hella company in the headlight was replaced by the Soviet FG 137, and the IZH UP1 lamps of the direction indicators were replaced by unified lamps 16.3726. There are other innovations as well.

Jupiter-4 is now also equipped with 12-volt equipment. The plant is preparing for production and new model"Planet-sport", the electrical equipment of which is unified with the "Jupiter-4".

However, already now the owners of Planet-Sport can use a number of IZH Yu-4 electrical appliances without significant alterations. These include generator 28.3701 (if it is sold without a breaker and a capacitor, they can be taken from the old IL GP1); direction indicator lights 16.3726; optical element of headlight FG 137; rear lamp FP146; speedometer SP102; rechargeable battery 6MTS-9.

To install the turn signal interrupter IZH RP2SM-10 into the headlight housing, it is necessary to make an additional bracket from a steel strip 1-1.5 mm thick and replace the plug-in tips with round ones. After the same alteration of the tips, the combined switches IZH P101-20 and IZH P102-20 from the IZH Yu-4 motorcycle can also be used on Planet-Sport. To do this, pressing the fixing antennae with an awl or a knitting needle, remove the plug tips. They are cut off and round lugs are crimped and soldered on the stripped ends of the wires. At the IZH P101-20 switch, a blue outlet wire 130-150 mm long with a plug tip is also soldered to the black wire.

The improvement of the electrical equipment of motorcycles and the use of new devices have naturally led to some complication of the electrical circuit. Let's get acquainted with its main elements using the example of the electrical equipment of the Planet-Sport scheme, which is in many ways similar to the schemes of other Izhevsk motorcycles.

Ignition system. This is perhaps the main system, because without it the motor cannot work. Let's trace and remember its electrical circuit. From the battery 24 through the fuse 25 and the rectifier 26, power is supplied to the terminal (2) of the connecting panel in the headlight housing and then to the terminal (3) of the ignition switch 9. When the key is turned to position I, the terminals (3-2 - 1 and 5 -6). Now, from the terminal (1) of the lock, the current goes to the terminal (5) of the connecting panel, from it to the emergency ignition switch 11, and through its closed contacts to the terminal (1) of the connecting panel and then to the primary winding of the ignition coil 21 (the second end of the primary winding - the "-" terminal is connected to the breaker). Thus, the circuit of the motorcycle ignition system is turned on.

If the engine does not run due to the absence of a spark at the plug, check if high voltage is being supplied to it. To do this, remove the wire from the cap and bring it to the edge of the cylinder with a gap of 2-3 mm. If, when the crankshaft is rotated by a kick starter, a spark does not appear between the wire and the cylinder - high voltage no. The reason for this is found as follows. When the ignition is turned on, a 12-volt test light is used to check whether power is supplied to the “+” terminal of the ignition coil. If not, then check the entire circuit, starting from the battery. A common cause of no voltage is loose or oxidized terminals, or a faulty fuse.

Having achieved that on the terminal "+" of the ignition coil appears normal voltage, carefully clean the breaker contacts, check and set a gap of 0.4-0.6 mm between them and adjust the initial ignition timing.

If the engine gives only separate flashes at start-up, and a white coating appears on the breaker contacts, it means that the capacitor has failed (rarely, but this happens).

With the correct clearance, clean breaker contacts and a working capacitor, the reason for the absence of a spark on the candle may be a malfunction of its plastic cap (breakdown to ground) or the ignition coil (it is non-separable, so it is replaced). A bad spark plug can cause the engine to misfire or make it difficult to start. Alarm and lighting system

direction indicator. When the ignition is turned on (the key is in position I), electricity from the battery 24 (or rectifier 26 when the engine is running) is supplied through the terminals (3 and 1) of the ignition switch 9 to the terminal (5) of the connecting panel. The power wire of the relay 6 of the direction indicators, the sound signal 18 and the "positive" wire of the light switch 11 located on the steering wheel are connected to it. From relay 6, power is supplied to the lights through the terminal (9) of the connecting panel and then to the switch 19 of the direction indicators. From it, through the terminals (6 and 7) of the connecting panel, it goes to the lights 10 and 28 of the direction indicators. The control lamp 16 of the direction indicators is also connected to the terminals (6 and 7) of the connecting panel through the block of diodes 7.

The reason for the failure of the direction indicators most often is the lack of "mass" in the lamps when their fastening to the frame is loosened, oxidation or loosening of the connections of the tips with wires, contacts in the lamp sockets.

To speed up troubleshooting, the circuit is checked from the idle consumer to the power source. To determine the operability of the relay 6 of the direction indicators without dismantling it, you must first make sure that the terminal (5) of the connecting panel is energized, and the brown wire of the relay is securely connected to ground. Then check the continuity of the circuits going to the direction indicator lamps by connecting terminal (5) with terminals (6 and 7) of the connecting panel with a separate wire. The lights of the right (terminal 6) or port side (terminal 7) and the control lamp 16, if the circuits are in good condition, should burn without blinking. Then disconnect the pink relay wire from terminal (9) and connect it to terminals (6 and 7) of the connection board. With a working relay, the lights of the starboard or port side should flash at a frequency of 60 to 120 per minute.

The relay removed from the motorcycle is checked using two A12-21-3 control lamps (power of each 25 W) connected in parallel. Connect the “plus” of a constant voltage of 12 volts to the red wire, “minus” to the brown one, and control lamps to the pink one. With a working device, the lamps should flash at a frequency of 90 ± 30 per minute.

Farah. It contains the main part wiring diagram, turn signal relay, neutral 3 and oil pressure warning lamps 5, lamp 8 illuminating the speedometer scale, parking light lamp 1, head light lamp 2, ignition lock 9 and speedometer.

On the latest models motorcycles, the turn signal breaker is mounted on the frame under the gas tank.

Consider the electrical circuit of the head, parking and clearance light. With the ignition on (key in position I), power is supplied to terminal (4) of the connecting panel, then through the contacts of the light switch 11 to the central contact of the high-dipped beam switch 19. Then through the terminals (11 and 12) of the connecting panel - to the thread of the high or low beam of lamp 2.

Side light in the headlight (bulb 1) and in rear light 29 lights up when the switch 11 is activated and current flows through the contacts (5 and 6) of the ignition switch 9.

If the ignition key is turned to position II (parking), then these lamps are powered through its contacts (3 and 5) regardless of the position of the switches on the steering wheel.

Lamps that dimly glow when the engine is not running indicate that the battery is not fully charged. If this is observed in all engine operating modes, it means that the voltage in the lamp supply circuit drops sharply. In this case, check the electrical connections of the power and ground wires, clean and tighten the screw and plug connectors, the contacts in the lamp sockets of the headlights and lanterns. Check the serviceability and reliability of the contacts in the switches and fuse.

Since the motorcycle is constantly being improved during the production process and its circuit diagram changes, it is advisable to include in the diagram printed here the differences of your motorcycle, so that, using it, you can always easily and quickly find the desired circuit and determine the malfunction.

V. SAMOILOV, engineer
Izhevsk

The road version of the IZH Planet 5 motorcycle favorably differed from others domestic analogues the use of an oil pump, which made it possible to abandon the scheme of preliminary mixing of fuel with oil.

In addition, subsequent modifications were distinguished by their non-contact ignition system, independent of the battery and modified kinematics.

This allowed:

1. Set the motorcycle in motion “from the pusher” - by turning on the ignition, the owner turned on the second gear and, by his own efforts, pushing the motorcycle forward, started the engine;
2. Operation without a battery was possible during daylight hours (for operation parking lights and headlights still required a battery).

According to the industry standard, the motorcycle had an alphanumeric index:

1. IZH 7.107-010 - basic model;
2. IZH 7.107-020 was already equipped new system lubrication and improved front axle suspension. In addition, the wiring diagram of the IZH Planet 5 motorcycle had contactless system ignition, independent of the battery;
3. IZH 7.107-030 was equipped with a spring-hydraulic shock absorber and a redesigned rear wheel brake drive;
4. IZH 7.107-040 was produced with modified kinematics and a modified front wheel brake. The wiring diagram on IZH Planet 5 remained non-contact until 2008.

In addition, a side trailer (sidecar) or a universal cargo platform (without a seat) could be attached to the motorcycle.

Electrical equipment IZH Planet 5

The motorcycle uses 12 volt electrical equipment. The electrical wiring of the IZH Planet 5 motorcycle is single-wire, the role of the negative wire is performed by a metal frame.

Among the main components are:

1. Power supplies;
2. ignition system;
3. Headlight;
4. Dimensional lighting and turns.

For reference: as is customary in auto and motorcycle construction, modification of components and assemblies allows you to reduce the cost of products.
For consumers, the advantage is that the price is low and a number of parts are interchangeable.

Generator

The motorcycle is equipped with a three-phase alternator having an electromagnetic excitation circuit.

The principle of its work is as follows:

1. Electric current from the windings located on the stator is supplied to the rectifier;
2. That converts it to direct current;
3. And delivers through the ignition switch to consumers.

The following items are included in the instructions:

1. Voltage regulator with rectifier BPV-14-10;
2. generator rotor;
3. Generator stator with windings;
4. Collector brushes;
5. Ignition cam (battery);
6. Contact node of the ignition system

For reference: on three-phase motorcycle generators IZH Planet 5, the windings are connected according to the “star” or “triangle” scheme.
The rectifier is installed as a separate unit, and the IZH Planet 5 electrical wiring is already connected to it.

Headlight

For reference: with a similar IZH generator, Planet 5 did not need an external current source when starting the engine.
Therefore, the battery was not included in the electrical equipment.

The headlight circuit includes:

1. headlight lamp (35W);
2. control lamp of blue color of inclusion (2W);
3. headlight parking light lamp (4W);
4. rear brake light lamp (15W).

control devices

The following controls are installed on the motorcycle:

1. speedometer with daily and total mileage counters;
2. tachometer with control lamps for direction indicators and head light;
3. engine temperature gauge;
4. voltmeter.

Maintenance features

Often, during operation, it is required to correctly set the gap between the contacts of the breaker. This requires tools and a diagram to see which elements need to be dismantled.

The algorithm of actions is as follows:

1. put the motorcycle on the stand;
2. turn on the neutral;
3. unscrew the spark plug from the cylinder;
4. remove the engine crankcase cover;

1. crank the crankshaft until the contacts are as open as possible;
2. use a screwdriver to loosen the locking screw;
3. using a special probe, set the gap to 0.35-0.45 mm and fix it with a screw;
4. collect everything in reverse order;

1. turn on the ignition and start the engine. His steady work Idling indicates a correct adjustment.

In general, all the wiring of IZH Planet 5 is very easy to do with your own hands.

The need for such work often arises when operating a motorcycle:

1. in wet weather, moving in the rain for a long time (oxidation or dampness of electrical contacts);
2. when traveling over rough terrain, abundant with vegetation and shrubs (mechanical damage to the wiring);
3. when operating in winter (snow and slush stick to the wires and can damage them).

Often, during operation, the sound signal also suffers. Its malfunctions manifest themselves in the form of a deterioration in sound quality.

To restore its performance, you must perform the following procedure:

1. loosen the locknut with an open-end wrench;
2. turn on the ignition;
3. press the button to turn on the sound signal;
4. adjust the tone with a screwdriver;
5. repeat the procedure until we get a clear and loud sound;
6. tighten the control nut.

Conclusions: we express confidence that this article will help you in servicing motorcycles of the IZH family (see also the article about). Both the attached diagrams and the description will allow you not to make mistakes during work.

Easily fixing breakdowns of the mechanical part, motorists experience difficulties if the electrician fails. Quite in vain, the wiring diagram of the planet Izh 5 is simple, it’s easy to figure it out.

For repairs, there is no need to have special stands and equipment. A minimum knowledge of electrical engineering and a simple avometer (tester) is enough, even often you can get by with just a test lamp.

Let's talk in more detail about the main components of the electrical wiring and possible malfunctions. The Izh Planet wiring diagram makes it easy to find a broken wire or insulation damage (for example, poor contact always heats up).

But pay Special attention The fact that the electrical circuit is designed not only for 12 volts, there is also a high-voltage cable (connecting the coil and the candle) cannot be checked with an ordinary ohmmeter.

In this case, we look to see if there is a spark at the output of the coil and at the output at the contact of the candle. Let us consider in detail about the main wiring nodes of Izh planet.

Generator

The heart is a generator (sometimes called a magneto, but they were never used on Izh Planet). Three windings produce alternating current. For stimulation, it is used instead permanent magnet extra coil. Therefore, it is impossible to start the motorcycle from the "swing" with a fully seated or missing battery.

A diode bridge for rectifying the current and a voltage regulator assembled in one unit are mounted on the Izh Planet 5 generator (they are not even singled out in the Izh Planet wiring diagram manuals).

Possible breakdowns in this node:

1. It is checked by measuring their resistance of current-carrying conductors and insulation. If the generator is damaged, it will noticeably warm up.
2. - the output voltage will be significantly different from the nominal level or absent.
3. Although the electrical circuit includes short circuit protection, it happens that the automation does not work and most often the output transistor burns out.

Battery

The motorcycle battery is weak. The motorcycle does not have a starter, so its only task is to supply voltage to the ignition system and the excitation winding of the generator during start-up. Thanks to the battery, designed for 12 volts, a stable start of the fifth Planet is ensured, up to the third model the wiring was 6 volts, and the ignition is not always clear.

Possible battery malfunctions:

1. - housings, plates, electrolyte leakage.
2. - determined by measuring with a hydrometer.
3. - detected by measuring the resistance.
4. minus not on the body (frame) of the motorcycle - all electronics will not work.

Ignition system

The ignition interrupter is used to ignite a spark at a certain point in the piston stroke. In early modifications of the electrical wiring of Izh Planet 5, a contact was mounted, later electronic.

The main malfunctions of this node:

1. Burning of the breaker contacts - determined visually.
2. Failure of a sensor or switch elements - the easiest way to detect is to use the method of installing a known-good unit. The sensor valve of the lubrication system is also checked in the same way.
3. An incorrectly set ignition timing is visible from the fuzzy operation of the motor. Eliminated by adjustment using special probes.

The ignition coil raises the voltage to several kilovolts so that the discharge can ignite a spark on the spark plug electrodes. The secondary winding is made of a rather thin wire, most often it burns out. Although a breakdown is also possible between the turns or on the body. The same troubles can (but less often) occur with the primary circuit. Everything is revealed with the help of resistance measurements.

Lamps for headlights and alarms.

Conventional incandescent lamps are used, it is not difficult to find a burned-out spiral.

Switching elements.

These include switches (high-low, turns, engine stop, etc.) as well as brake and neutral sensors and an ignition switch. You can easily “ring” them with a tester, finding out which contact Group does not work.

Switching also includes the electronic turn relay Izh. Its malfunction is visible by the absence of interruption or even supply of voltage to the turn signals.

As can be seen from all of the above, the wiring to Izh Planet without any special secrets and complex elements, all its parts are easily diagnosed and repairs should not cause difficulties.

And now we advise you to watch the video, which shows in detail and clearly the assembly of the Izh planet 5 circuit.

The IZH Planet 5 wiring diagram has a simple design: a single-wire DC network is provided by a 12-volt battery, which is charged by a 100–140-watt generator. The role of the negative wire in the electrical circuit is performed by the metal frame, and since the rest of the wiring has a positive charge, their short circuit is often the main cause of the malfunction.

[ Hide ]

Electrical equipment IZH Planet 5

Posting IZH Planet 5 includes:

• generator;
• battery;
• ignition system;
• headlights;
• control devices;
• switching elements.

Video: IZH Planet 5 wiring review

Taken by Agronomist.

Generator

Generator device IZH Planet 5:

• voltage regulator with rectifier BPV-14-10 - 1;
• rotor - 2;
• stator with windings - 3;
• current collector brushes - 4;
• cam of the ignition system (battery) - 5;
• contact assembly of the ignition system - 6.

The generator converts mechanical energy gasoline engine into electricity to charge the battery. Alternating current is generated by 3 windings and fed to a rectifier, which converts it to direct current. An additional coil is used as the exciter.

Photo gallery: IZH Planet 5 generator and its device

Generator IZH Planet 5 Generator device

Battery

To supply all components, a low-power energy storage device of exactly 12 volts is required, since there is no starter in IZH Planet 5. Task lead acid battery only apply voltage to the ignition system and the excitation winding of the generator during start-up.

Battery

Ignition system

In IZH Planet 5, the ignition coil converts low-voltage voltage to high-voltage and transfers it to the spark plug. That, in turn, is responsible for the spark that detonates the fuel. In order for detonation to occur only in the desired position of the piston, there is an ignition interrupter.

Ignition system

In the factory, this model has a classic ignition system, which requires periodic cleaning of the breaker contacts and adjusting the gap between them.

Installing contactless coolant on a motorcycle gives:

• timely powerful sparking;
• reduction of vibration level;
• reduction in fuel consumption.

control devices

The motorcycle has the following controls:

• tachometer, on which there are control lights for head light and turns;
• speedometer showing total and daily mileage;
• power engine temperature gauge;
• voltmeter.

control devices

Headlight and instrument panel lamps

As lighting equipment and for lighting dashboard conventional incandescent lamps are installed. Switching elements are responsible for supplying electricity from the battery to the lamps.

The headlight circuit includes lamps:

• headlight headlights (35 watts);
• parking light headlights (4 W);
• control - blue switching on (2 watts);
• rear brake light (15 W).

Headlight

Switching elements

Switching elements are various kinds of switches that close or open an electrical circuit. They can be activated using the keys on the dashboard (for example, turn signals) or by sensors.

In IZH Planet 5, switching elements include:

• turn switches;
• signal key;
• low / high beam switches;
• neutral gear sensor;
• egnition lock;
• foot and hand brake sensors.

Wiring diagram IZH Planet 5

Detailed color wiring diagram for moto IZH Planet 5

Explanations for the scheme

The numbers on the wiring diagram correspond to the following elements:

1. Light toggle switch, dimensions / dipped.
2. Light switch, direction indicators and horn buttons.
3. Front turn signals.
4. Illuminated instrument panel.
5. The control lamp of the generator.
6. Oil pump indicator.
7. Light bulb reflecting the operation of the neutral gear in the checkpoint.
8. Direction indicators.
9. Headlight high beam indicator.
10. Front position light bulb.
11. Headlight lamp.
12. Sound signal.
13. Hall Sensor.
14. Generator.
15. Egnition lock.
16. Relay-interrupter of direction indicators.
17. Neutral indicator light sensor.
18. Block BPV 14-10.
19. Switch.
20. Battery.
21. Fuse.
22. Relay block.
23. Ignition coil.
24. Foot brake sensor.
25. Rear direction indicators.
26. Tail light with lamps.

Description of symbols for outputs on the block rectifier-regulator BPV 14-10:

• –x1 - “minus” of the generator excitation winding;
• –x2 - “minus” of the accumulator (“mass”);
• x2 - "positive" wire to the control lamp of the instrument panel;
• x3 - "positive" wire to the shield indicator;
• x4, x5, x7 - phases of the stator winding;
• x8 - "plus" battery.

Maintenance

Owner can perform some procedures on his own Maintenance:

• check the motorcycle alternator if the battery loses charge;
• set the gap between the contacts of the breaker;
• adjust the sound quality.

The need for inspection and adjustment of the wiring operation arises if:

• the motorcycle moves in the rain for a long time, as this causes oxidation of the contacts;
• a motorcyclist rides in an area where there is a lot of vegetation that damages the wiring;
• the driver rides in winter on snow, which can stick to electrical wiring parts and damage them.

Self-test of the Planet 5 motorcycle generator in case of loss of charge

The reason for the loss of charge in the IZH Planet 5 battery is most often a breakdown of the generator.

To check with your own hands you need:

• multimeter instrument;
• straight screwdriver.

Step-by-step instruction

The following steps must be followed:

1. Disconnect the wires from the battery and remove the generator cover.
2. Disconnect the 5 upper wires from the generator by unscrewing their fasteners before that. In order not to confuse the wires during assembly, it is worth marking them.
3. Measure the resistance of the windings using a multimeter in ohmmeter mode. To do this, you need to touch one probe to the body, and the other should be connected in turn to 3 winding wires. There should be no short circuits, as indicated by the inscription on the screen of the multimeter.
4. Test the resistance between the stator contacts: you need to touch them in turn with the probes of the multimeter. The value on the screen should be 8 ohms.

The presence of a short circuit at the 3rd stage or a discrepancy between the indicators at the 4th stage will indicate problems with the generator.

Photo gallery: stages of checking the IZH Planet 5 generator in case of loss of charge in pictures

Stage number 1. Photo disconnecting the generator from the battery Stage number 2. Disconnecting the wires from the generator Stage number 3. Measurement of winding resistance Step #4: Resistance Testing

How to correctly set the gap between the contacts of the breaker?

In order to set the gap between the contacts of the breaker, you will need:

• straight screwdriver;
• wrench for 10;
• key for candles;
• probe 0.4 mm thick (+/- 0.05 mm).

1. Mount the motorcycle on a stand, transfer the box to neutral.
2. Remove the right crankcase cover and unscrew the spark plug.
3. Using a 10 wrench, grab the alternator rotor mounting bolt and turn the crankshaft to a position where the contacts are as far apart as possible.
4. Loosen the contact attachment screw.
5. Place the probe between the contacts and adjust the tightening of the eccentric screw until the probe passes the contacts with little resistance.
6. Tighten the contact attachment screw.