Wheel sizes for Mazda cars. About the bolt pattern characteristics of Mazda wheels Standard wheels for Mazda 6
When choosing a wheel for a Mazda car, special attention should be paid to the parameters of the wheels and tires. For each passenger car model, Japanese manufacturers use separate standard sizes. For example, the factory equipment of the Mazda 6 requires the use of 195/65/R15 tires. As an alternative, you can use tires 205/50/R17, 205/60/R15, 225/40/R18, 225/35/R19.
Wheel size for Mazda 6 I GG
- increased load on the hub bearings;
- loss of aerodynamic performance;
- reducing the vehicle's directional stability.
In addition, indicators such as fuel consumption, handling and safety when driving a car also depend on the choice of wheel sizes.
Before choosing a wheel for a Japanese car, you need to study its parameters:
- tire width;
- profile height;
- speed and load capacity indices;
- tire pressure;
- diameter;
- departure;
- number of fastening elements;
- types of fasteners;
- circle parameters;
- center hole.
When choosing non-standard wheel sizes, you can use a tire calculator. This device is capable of selecting the optimal sizes of wheels and tires, the wheel load index, taking into account the vehicle speed and ground clearance.
Wheel sizes for Mazda 6 version GG 2002-2008:
- thread diameter: 5.
Tire size for Mazda 6 GG
We present a table where we indicate the wheel load indices, speeds, sizes and tire pressures on the GG version.
| Wheel load index | Tire parameters | Tire pressure kg/cm² | Speed index |
| 91 | 195/65/R15 | 2.2 | V |
| 93 | 205/60R16 | 2.2 | V |
| Replacement | |||
| 91 | 215/45/R17 | 2.2 | V |
| 91 | 215/50/R17 | 2.2 | V |
| 89 | 215/45/R18 | 2.2 | W |
| 91 | 225/45/R18 | W | |
Wheels for Mazda 6 GG
| Size | Disc offset | |
| 5×114.3 | 6Jx15 | ET50 |
| 5×114.3 | 6.5Jx16 | ET55 |
| Replacement | ||
| 5×114.3 | 6.5Jx16 | ET55 |
| 5×114.3 | 7Jx16 | ET55 |
| 5×114.3 | 7Jx17 | ET55 |
| 5×114.3 | 7Jx17 | ET60 |
| 5×114.3 | 7Jx17 | ET60 |
| 5×114.3 | 7Jx18 | ET55 |
| 5×114.3 | 7.5Jx18 | ET60 |
Wheel size for Mazda 6 II GH
- 205 indicates the width of a car tire. This indicator is measured in millimeters and is determined by calculating the distance of the side edges of the inflated tire. This does not take into account protective belts;
- 60 shows the profile height of the tire, measured as a percentage of the width of the tire. Thus, to determine the height, you need to know the ratio of 205 mm to 60%. As a result, we calculate the profile height: (60%/100%)X 205= 123 mm;
- R indicates the radius of the tire. Translated from English, Radial is the radius of a car tire. Thus, manufacturers combine rubber and cord when creating a tire. The letter D was also used to designate radiality. However, tires with this designation are practically no longer produced;
- 16 indicates the diameter of the wheel centering hole for which a car tire can be used. This indicator is indicated in inches.
Mazda 6 GH 2007-2012 model year:
- center hole diameter DIA: 67.1 mm;
- hub fastening element: nut;
- thread: M12x5.
Additional information indicated on the side of the tire:
M&S (Mud and Snow) translated from English: mud and snow: off-season and winter tires;
XL (Extra Load) reinforced tire with a wheel load index that is 3 units higher than conventional tires with similar sizes;
AW or AS off-season tires;
Symbol * indicates that the tire is intended for use in winter. If this marking is not indicated on the side of the tire, then the tire is used only for the summer period;
Inside, Outside– inner and outer side of an asymmetric tire. Accordingly, when installing a wheel, the Inside sign should be located on the outside of the tire, and the Outside sign on the inside of the tire;
Water, Rain, Aquatred, Aqua or an umbrella-shaped symbol indicates rain tires;
Tubeless inscription- tubeless tire. If there is no inscription, this means that the tire is used with a tube. Tube Type indicator – the tire is installed only with a tube;
Arrow or inscription Rotation shows the direction of the tread pattern. Indicated on the side of the tire.
Wheel size for Mazda 6 III GJ
For the Mazda 6 III GJ, standard wheel size markings are used, as for other Japanese car models.
Before choosing a wheel product, you need to study the standard parameters of the factory-fitted rim 7.5×17 5×114.3 ET50 for the GJ version, where:
- 7.5 shows its width in inches;
- the symbol J indicates the design, the shape of the edges;
- the number 17 indicates the diameter of the disc seat. This indicator must correspond to the same parameters of the tire;
- 5×3 – PCD disc bolt pattern. The number 5 indicates the number of holes for fastening the nuts, 114.3 indicates the diameter of the PCD circle;
- The ET50 marking indicates a disc offset of 50 mm. The offset is the distance from the mating plane of the car disk to the middle of the wheel rim. The area where the wheel rim is pressed against the car hub is called the mating plane.
The following information is attached to the markings of rims for Mazda GJ 2012-2015:
The Max Load inscription indicates the maximum permissible load on the wheel;
ISO, TUV, SAE – classification standards for determining disk quality, similar to GOST. For each product, one or another quality standard is indicated;
Center hole diameter DIA: 67.1 mm. This indicator must correspond to the hub landing diameter. For casting, manufacturers use a large centering hole. So that the wheels can be universal for all types of cars.
However, in this situation, the hub fit diameter and DIA are different from each other. Therefore, it is recommended to use a centered adapter ring as a connecting element.
The correct choice of wheel size also depends on the ability to determine the markings of the wheel and tire. If the car owner does not know the marking designation, then the selected tires or wheels may not be suitable in size.
Wheel sizes for Mazda 6 III GL
The Mazda 6 version GL has been produced since 2015. Wheel parameters:
hub fastening element: nut;
thread M12x1.5;
Tires for Mazda III GL
Wheels for Mazda III GL
Please note that the drilling or bolt pattern indicates the fit of the wheel rim diameter. In the car's operating instructions, Japanese manufacturers indicate PCD, bore diameter.
On Mazda cars, 3 different versions and editions use the same disc bolt pattern: 5 × 114.3. Thus, this drill determines that the disk is attached with 5 bolts and its diameter is 114.3 mm.
Mazda 3 wheel size
| Diameter, R | Tire size | Disc offset, ET | Disc width, J | |
| 5×114.3 | R15 | 195/65/15 | 45-55 | 66.57.0 |
| 5×114.3 | R16 | 205/55/16 | 40-5540-5542-55 | 6.577.5 |
| 5×114.3 | R17 | 205/50/17215/45/17225/45/17 | 42-5545-5548-52 | 77.58 |
| 5×114.3 | R18 | 215/45/18225/40/18215/40/18 | 42-5542-5545-52 | 77.58 |
| 5×114.3 | R19 | 225/35/19225/35/19 | 45-5548-52 | 7.58 |
| 5×114.3 | R20 | 225/35/20 | 45-48 | 7.5 |
The wheel parameters for Mazda 3 I and II editions are almost identical. The differences are that the second version of the car has higher arches.
Thus, on the Mazda 3 II BL you can mount wheels with an offset of 35 and a width of 8. The standard parameters are 16.17-inch wheels with a diameter of 6.5 mm.
Wheels for Mazda 3 2013, III generation BM
| Drilling (PCD, bore diameter) | Diameter, R | Tire size | Disc width, J | Disc offset, ET |
| 5×114.3 | R16 | 205/60/16 | 6..5 | 50 |
| 5×114.3 | R17 | 205/50/17 | 7, 7.5 | 52.5 |
| 5×114.3 | R18 | 215/45/18 | 7, 7.5 | 50 |
| 5×114.3 | R19 | 215/35/19 | 8 | 50 |
| 5×114.3 | R20 | 235/30/20 | 8.5 | 45 |
Factory wheel sizes for Mazda 3 with hatchback and sedan body types from 2013-2017 are 16, 18 inches, depending on the configuration. Tires with standard sizes are installed: 215/45/R18, 205/60/R16.
Tire pressure on Mazda 3
When using R16 tires with a load of up to 3 passengers, the pressure of the front and rear wheels should be 2.5 bar. With a load of up to 5 passengers, the rear tire pressure is 3.2 bar and the front tire pressure is 2.8 bar.
R18 tires with a load of up to 3 passengers should have a pressure of 2.4 bar for the front wheels and 2.3 for the rear tires. Full load up to 5 passengers - rear tire pressure 3 bar and front tire pressure 2.8 bar. Similar information is indicated in the operating instructions for the Mazda 3 III generation.
How to determine the drill yourself?
Method for determining wheel rim bolt pattern:
- the number of fasteners (bolts) is calculated based on the holes located on the disk. For example, Mazda 3 has 5 holes in the disc;
- the calculation includes determining the distance between the inner walls of the holes and adding to the resulting value of their diameter.
For example, having determined the number of bolts and the diameter of the holes, the car owner gets the value 5 × 114.3 for Mazda 3.
An exception may be 18-inch wheels for Mazda 3 with a front drive axle and a 2.0 engine capacity, as well as versions with all-wheel drive and a power of 2.5 liters.
Wheel size for Mazda CX5
All trim levels of the Mazda CX5, starting from 2012, use 17 and 19-inch alloy and steel wheels marked 17x7J ET50, 19x7J ET50:
- ET – disc offset 50 mm;
- 7J – rim width;
- the diameter of the centering hole is 67.1 mm and 5 holes for fastening bolts around the circumference of the disk 114.3 mm; PCD 5x3.
The Mazda CX5 can be equipped with wheels with non-standard parameters (-+0.5) inches.
Tires for Mazda CX5
If you use factory wheels of 17, 19 inches, then for the CX5 model tires with the following sizes are selected: 225/55/R19/ 99 V, 225/65/R17/ 102 V. Marking designation:
- 225 – tire width;
- 55.65 – tire profile height;
- 99.102 – load capacity index from 750 to 850 kg;
- V – wheel speed index up to 240 km/h;
- R – radial tire design.
If you choose tires based on the load capacity index, then you need to take into account the fact that the estimated weight per person is 75 kg. As a last resort, you can calculate the number of passengers and install tires with a high load capacity.
| Size | Load index | Speed index | Pressure, kgf/cm² |
| 195/65R15 | 91 | V | 2.2 |
| 205/60R16 | 93 | V | 2.2 |
| Replacement | |||
| 205/55R16 | 91 | V | 2.2 |
| 205/55R16 | 91 | V | 2.2 |
| 215/45R17 | 91 | W | 2.2 |
| 215/50R17 | 91 | V | 2.2 |
| 215/50R17 | 91 | W | 2.2 |
| 215/45R18 | 89 | W | 2.4 |
| 225/45R18 | 91 | W | 2.2 |
Disk
| Size | Departure | Sverlovka |
| 6Jx15 | ET50 | 5×114.3 |
| 6.5Jx16 | ET55 | 5×114.3 |
| Replacement | ||
| 6.5Jx16 | ET55 | 5×114.3 |
| 7Jx16 | ET55 | 5×114.3 |
| 7Jx17 | ET55 | 5×114.3 |
| 7Jx17 | ET60 | 5×114.3 |
| 7Jx17 | ET60 | 5×114.3 |
| 7Jx18 | ET55 | 5×114.3 |
| 7.5Jx18 | ET60 | 5×114.3 |
Mazda 6 II GH
205 – tire width. The indicator is calculated as the distance between the outer boundaries of the side surfaces of the inflated tire without taking into account the protective belts. Measured in millimeters.
60 – tire profile height, which measured as a percentage of the width. What does it mean? To find the height, you need to calculate 60% of 205 mm. This gives the tire height: 205 X 0.6 (60%) = 123.0 mm
R stands for radial tire. From the English word Radial, which means radial type of tire. This is a method of arranging rubber and metal cord during production. Of course, you can also find the letter D - diagonal, but such tires have now practically disappeared from production.
16 — the diameter of the hole in the rubber, or on which disk this rubber can be mounted, that is disk diameter. This size is always indicated in inches!
The diameter of the disc cannot be larger or smaller than the diameter of the wheel; you simply won’t fit it. That is, if the tires are 16 inches (406.4 mm), then the rim should be 16 inches (406.4 mm)!
Additional information
Mazda 6 GH, years of production: 2007 – 2012.
- Fastening to the hub: nut;
- Thread: M12 x 1.5.
Additional information indicated in the markings on the sidewall of the tire:
- XL or Extra Load is a reinforced tire, the load index of which is 3 units higher than that of conventional tires of the same size.
- M+S or M&S (Mud + Snow) - mud plus snow - winter and all-season tires.
- All Season, AW (Any Weather) or AS - all-season tires
- The pictogram * (snowflake) means that the tire is intended for use in winter conditions. If there is no this marking on the sidewall of the tire, then this tire is intended for use only in summer conditions.
- Aquatred, Aquacontact, Rain, Water, Aqua or pictogram (umbrella) - special rain tires.
- Outside and Inside are asymmetrical tires; during installation, it is important not to confuse which side is outer and which is inner. When installing, the inscription Outside should be on the outside of the car, and Inside should be on the inside.
- Rotation or arrow - this marking on the sidewall of the tire indicates the directional tread pattern of the tire. When installing a tire, you must strictly observe the direction of travel.
- Tubeless - tubeless tire. If this inscription is absent, the tire can only be used with a tube. Tube Type - means that this tire must be used only with a tube.
Tire
| Size | Load index | Speed index | Pressure, kgf/cm² |
| 205/60R16 | 93 | V | 2.2 |
| 205/60R16 | 92 | V | 2.2 |
| Replacement | |||
| 215/50R17 | 91 | V | 2.2 |
| 215/50R17 | 91 | W | 2.2 |
| 225/45R18 | 91 | W | 2.2 |
| 225/45R18 | 91 | V | 2.2 |
Disk
| Size | Departure | Sverlovka |
| 6.5Jx16 | ET55 | 5×114.3 |
| 6Jx16 | ET50 | 5×114.3 |
| Replacement | ||
| 7Jx17 | ET60 | 5×114.3 |
| 7Jx17 | ET60 | 5×114.3 |
| 7.5Jx18 | ET60 | 5×114.3 |
| 7.5Jx18 | ET60 | 5×114.3 |
Mazda6 III GJ
Regardless of the method of production of disks - cast, forged, stamped, there is a standard marking of disk sizes.
Let's look at the main parameters of 6 GJ - 7.5Jx17 5x114.3 ET 50.
7.5 - rim width in inches. Converted to millimeters it turns out to be 190.5 mm.
J - the symbol indicates certain design features - the shape of the edges of the disk and serves only for information.
17 is the mounting diameter of the rim in inches, which exactly matches the mounting diameter of the tire.
5x114.3 - PCD (Pitch Circle Diameter) or drilling in Russian. Here, the number 5 indicates the number of mounting holes for the nuts, and 114.3 is the diameter of the circle (PCD) in millimeters on which they are located.
ET 50 - the offset of this disc is positive and is 50 mm. Disc offset (or offset) is the distance between the mating plane of the wheel disc and the middle of the wheel rim. The mating plane is the surface that presses the wheel rim against the vehicle hub.
Additional information
Additionally, marking 6 GJ, 2012-2015 may indicate the following information:
- DIA D 67.1 - diameter of the central hole in mm. In an ideal situation, this size corresponds to the landing diameter of the hub. On many manufactured alloy wheels, for greater versatility and applicability to various car brands, the diameter of the central hole DIA is made larger. In this case, the hub fit diameter is smaller than the disc DIA, and then it is necessary to use a special centering fit ring (adapter ring).
- MAX LOAD - designation of the maximum load on the wheel (indicated in pounds or kilograms).
- SAE, TUV, ISO - an analogue of our GOST, the regulatory body. Indicates the standard to which the marking of this wheel corresponds.
Tire
Disk
Mazda Mazda6 III GL
Years of production: since 2015.
Additional information
- Center Hole Diameter (DIA): 67.1 mm;
- Fastening to the hub: nut;
- Thread: M12 x 1.5.
Tire
Disk
The tire and wheel markings contain a lot of necessary information; it is important to be able to understand it. Without this information, you will not be able to choose the right tires for your car; they simply will not fit in size. There are special signs on the car body with recommendations for tire sizes, just read them and go to the store for new ones. However, such signs are not always available, and you have to determine the size of Mazda 6 tires yourself!
Using automatic selection of tires and wheels for the car Mazda 6, you can avoid many problems associated with their compatibility and compliance with automaker recommendations. After all, they have a huge impact on a significant part of the vehicle’s operational properties, primarily on handling, fuel efficiency and dynamic qualities. In addition, one cannot fail to note the importance of tires and rims as active safety elements. That is why their choice should be approached as responsibly as possible, i.e. with knowledge of a number of parameters of these components.
Unfortunately, only a small part of car owners know such technical nuances. However, an automatic selection system will be extremely useful regardless of this, as it will minimize the likelihood of choosing the wrong rims or tires. And there is plenty to choose from, thanks to the widest range of such products presented in the Mosavtoshina online store.
Mazda 6 is a passenger car from the Japanese concern of the same name.
Since the presentation of the Mazda 6 model until the end of 2018, three generations have been released, namely:
- Mazda 6 GG between 2005 and 2007;
- Mazda 6 GH in 2010;
- Restyled version in 2011;
- Third generation at the beginning of 2012.
The changes affected not only the exterior, but also the interior, technical characteristics, power unit, and transmission.
Sizes of standard wheels for the Mazda 6 generation
| Mazda 6 (2002 - 2007) | |
|---|---|
| Original (tire) | 205/60 R16 |
| Replacement | 205/55 R17, 215/55 R18 |
| "Factory" equipment with disks | R16 5x114.3 6J ET50, (6.5J), (ET55) |
| Disk options | PCD: 5x114.3, DIA: 67.1, Nut: 12x1.5 |
| Replacement | R17 5x114.3 7J ET50, ET60, R18 7.5J |
| Mazda 6 (2008 - 2012) | |
| Factory configurations | 205/60 R16 |
| Replacement | 205/55 R17, 215/55 R18 |
| --/-- | R16 5x114.3 6J ET50, R17 5x114.3 7J ET50 |
| Mazda 6 (2013 - 2015) | |
| Original | 225/55 R17 |
| Replacement | 225/45 R19 |
| Mazda 6 (2016 - 2021) | |
| Original | 205/60 R16 |
| Replacement | 225/55 R17, 215/55 R18 |
| --/-- | R16 5x114.3 6J ET50, R18 5x114.3 7.5J ET60 |
Alternative wheel options for Mazda 6
- Cast: light weight, low pressure on support bearings, hub, transmission;
- Stamped: durable, expensive;
- Forged: durable, one third lighter than analogues.
| Name | Manufacturer |
|---|---|
Light alloy | AITL – 534, 605 Alcar - Hybrid Allante - 184 (HB), 561 Alutec – Freeze, Grip, Ikenu, Monstr, Raptr, Singa, Xplosive Angel - Hornet 601, Rapide 609 Arbet - 1 ATS – Emotion, Streetrally Autec – Hexano, Ionik, Nordic, Polaric, Quantro, Skandic, Wizard, Xenos, Yucon, Zenit Autom – 569, 803 Borbet – CA, F Disla – Evolution, Formula |
Stamped | KFZ – 6525, 7503, 7625, 7855, 7856, 8005 ZW - BK5372 (BP) Tech Line - 640 Thomason - TN11 TRW - Z1108 (DGMF) Vossen - CV3, VFS-5 Wheel Master - 0366 WSP Italy - W1704 ZD-21 ZF - FM039 (BMF) |
| Replica - Mazda SSL016 (HS), NS5264 Rial-Arktis Sportmax Racing - 1235 Storm - BK-438 Tech Line - 1603 Lawu - SL-511, YL-245, YL-828 LSW-L-335 Mac - Nitro Marcello - MR-07 PDW-8052 Racing Wheels - H-126 RC Design - RC-11 Replay - NS38 |
|
European brands | Disla Assassin Black Matt, Gunmetal Diamond Dotz Dakar Hamann HA1005 (MB) (BMW) Kapitan Berlingo/Partner 1998-2002 Black Kormetal KM 225 Firebird, KM 250, KM 245 Tornado Kosei RX SUV Replay A101 (GMF), A25 (GMF) Replica legeartis A47 (SF), A513 (BKF), A521 (BKF) Tech Line 311 BD, 503 BD, 526 BD Vianor VR13 (SF), VR16 (BKF), VR29 (GMF), VR32 (SF) WSP Italy T562 Amalfi AU62 Silver, W1006 Cayenne PO06 Chrome, W1050 Philadelphia Anthracite Polished, W1052 Corsair GT3/RS FL.F PO52 Glossy Black |
*check prices in stores at the time of purchase.
- Check wheel balancing on a special diagnostic stand in the workshop. If deviations are detected, restore the geometry of the structure. It is impossible to “reanimate” the disk on your own due to the lack of necessary equipment;
- If you find cracks or dents on the rim, contact a service station for preventive maintenance and rolling;
- At high and medium speeds, avoid getting into holes and potholes. The disc will be deformed, the seal will be broken, and the tire cord will be damaged;
- Monitor the tire pressure; it should not differ from that recommended by the manufacturer. If there is a deviation, pump it up yourself, contact the service station;
- Observe the transition to summer and winter modes. In summer, the tire pressure is 0.15 atm higher, in winter it is lower by the same amount. The parameters are specified in the vehicle operating instructions;
- Tighten the rim nuts with a torque wrench. Excessive tightening contributes to breaking the studs, weak - unscrewing. Which will lead to a collision on the road with an oncoming traffic participant.
In sunny weather, cast aluminum wheels are less susceptible to external damage. But in slush, ice, when the road is strewn with chemicals, the rim is susceptible to corrosion. This provokes peeling of the paint, destruction of the molecular composition, and a decrease in the strength of the structure.
Wash your wheels as they become dirty. Since it is unlikely that you can clean it properly with a rag, use high-pressure compressors. Equipment of this class is available in many service stations, workshops, and service centers.
Systematic polishing removes scratches. First clean the wheel from dirt, dry it thoroughly, and then treat it with a chemical. Wipe with a cloth several times.
Store wheels in a hanging position, do not stack them on top of each other. Clean off any dirt, dry, and wrap in cellophane. Some motorists practice applying an aerosol to the surface before preservation.
The average service life of original wheels is 180 – 200 thousand km. Subject to a moderate driving style, the replacement interval will increase by a third. The service life of tires is 70 – 80 thousand km.
What is the effect of installing wheels of non-standard sizes on a Mazda 6 car?
The size of tires and wheels influence the technical characteristics of the car. The instruction manual indicates the recommended and acceptable dimensions.
For a driver who uses the car as a means of transportation, the “factory” (stock) rim sizes are more than enough. In case of tuning, changes in standard characteristics, dynamic indicators, “re-shoe” the car with non-standard wheel sizes.
The list of characteristics that are changed by installing non-standard wheel sizes on a Mazda 6 car:
- Controllability;
- Road grip;
- Sharp, responsive steering wheel;
- Hydroplaning;
- Comfort;
- Noise level;
- Combined cycle fuel consumption;
- Tread wear.
Decoding the markings of wheels and tires on Mazda 6
For example, R19 5×114.3 6.5J ET50 (see photo):
- PCD (Pitch Circle Diameter) diameter of the circle of the center of the mounting holes: 71 mm;
- Disc radius: by 19;
- Number of holes 5;
- Fastener type: M11.0 – stud diameter;
- Thread size (pitch): 1.25;
- Center hole diameter: 67 mm;
- Pressure (front / rear): 2.0 / 2.0 bar.
PCD parameter: distance between the centers of opposite holes. Measure the value with a ruler without removing the wheel. For a five-bolt structure, the resulting distance must be multiplied by a factor of 1.05.
Rim offset (“ET”): The distance between the point where the rim meets the hub and the middle of the rim width. Designation: DEPORT, OFFSET. The offset is positive if the plane does not extend beyond the point of contact, otherwise the offset is negative. The further the rim is from the body, the more the offset tends to zero.
- D is the diameter of the central hole, measured in millimeters.
- J, H and subsequent alphabetical symbols indicate the markings of the humps on the rim flange. Symmetrical, asymmetrical and combined.
- The "hump" is a protrusion on the rim for a tubeless tire. When moving, the “rails” hold the tire beads, preventing depressurization.
Numerical characters indicate the release date, month, year.
- TUV is an abbreviation of the regulatory body for compliance with quality standards.
Maximum wheel load: the unit of measurement depends on the country of manufacture of the rubber and rim.